Before you buy, check it isn't under a dangerous recall.

The Driver Assistance System Control Unit had insufficient verification during software development. When Active Lane Assist is engaged and steering intervention occurs before crossing lane dividing lines, the minimum warning display time …

The Driver Assist System Control Unit had insufficient verification during software development. When Active Lane Assist is engaged and steering input intervention occurs before crossing lane markings, the minimum warning display time …

In the drive shaft, due to improper assembly work instructions at the manufacturing plant, some fastening bolts of the coupling that transmits power from the gearbox are not tightened to the specified …

The ABS unit control program is inappropriate. If a driver starts the vehicle without fastening the seatbelt and without disengaging the electric parking brake, the control program incorrectly detects the vehicle as …

In mid-size trucks with dual rear axle drive, the oil lubrication structure of the inter-differential section is inadequate, causing differential oil to reach excessively high temperatures during operation. This increases internal pressure …

Brake pipe connectors have inadequate manufacturing equipment control resulting in poor machining precision and defective sealing between the connector and brake pipe. Continued use may cause brake fluid leakage from the connector …

The combination meter brake warning light control program contains an error. The brake warning light does not illuminate during the warning light operation check at engine start. Additionally, if a brake malfunction …

In small buses, brake light switch assembly instructions contained errors, resulting in some units being assembled with pushrod protrusion less than the specified value. Consequently, the brake light may not illuminate when …

(1) In the automatic transmission, insufficient review of multi-plate clutch disk geometry and drive control may result in clutch not disengaging when shifted to Neutral. This could cause drive force to be …

(1) In the automatic transmission, insufficient review of multi-plate clutch disk geometry and control of power transmission may result in the clutch not disengaging when shifted to Neutral. This could allow power …

In tank semi-trailers, brake tube installation may be improper, causing interference between the brake tube and cargo discharge piping. Continued operation may result in brake tube rupture and air leakage, reducing braking …

The turbocharger oil delivery pipe has manufacturing control deficiencies, resulting in some pipes that do not meet specified standards during forming. Cracks can develop in non-conforming sections, causing oil leakage, which may …

Due to improper software in the lighting control unit, when the door is locked using the locking switch on the front passenger door, only the turn signal on the left side of …

In high-pressure fuel pumps for large trucks and buses, insufficient fuel film thickness between the tappet and roller, and between the roller and cam, causes wear on these sliding surfaces. This can …

The clamp securing the rear brake pipe to the frame has insufficient holding force. If the brake pipe detaches from the clamp, it may approach or contact the exhaust pipe. This allows …

The motor control unit (MCU) throttle operation output correction program is inappropriate. When referenced parameters fall below a certain threshold, incorrect calculation results may occur. This can cause unintended deceleration in the …

The vehicle harness cover is assembled with insufficient clearance to the left rear brake pipe due to improper wiring design. During vehicle operation, vibration and other forces may cause the harness cover …

In the electric power steering system, due to an inappropriate motor control program, when external temperature is low, input current to the electric assist motor becomes unstable, causing assist force to vary. …

Due to improper assembly instructions at the manufacturing facility, the heat shield mat may not be correctly installed on the brake fluid reservoir tank. As a result, the edge of the reservoir …

In the 48V hybrid system wiring assembly process, inadequate work management resulted in some positive cable attachment nuts being torqued below specification. Consequently, fastener loosening may occur due to vibration during driving, …

On vehicles equipped with ESC (Electronic Stability Control), there are instances where the ESC actuator and brake pipe connection is incorrect. This may result in unstable vehicle behavior during ESC operation or …

The fuel pump impeller (resin-molded impeller blade) may have inadequate molding conditions resulting in low resin density. This causes the impeller to swell and deform when exposed to fuel, potentially contacting the …

The impeller (resin-made rotor blade) of the low-pressure fuel pump may have reduced resin density due to improper molding conditions, causing it to swell and deform when exposed to fuel. This can …

The impeller (resin-made rotor blade) in the low-pressure fuel pump may have low resin density due to improper molding conditions, causing swelling and deformation when exposed to fuel. This can result in …

The impeller (resin-molded rotor) in the low-pressure fuel pump of gasoline engine vehicles may swell and deform due to low resin density caused by improper molding conditions. This causes the impeller to …

The fuel pump impeller (plastic rotor) used in replacement repair parts may have reduced plastic density due to improper molding conditions, causing it to swell and deform when exposed to fuel. This …

The fuel pump impeller (resin rotor) may have reduced resin density due to improper molding conditions, causing it to swell and deform when exposed to fuel. This can cause the impeller to …

In the brake piping, the flare nut fastening the brake pipe to the ABS unit was improperly tightened during assembly, resulting in insufficient fastening torque on some units. Continued use in this …

Due to inappropriate programming in the lighting control unit, operating the light check function button on the remote key causes all lights including brake lights and reverse lights to repeatedly cycle on …

Due to improper programming in the lighting control unit, operating the light check function button on the remote key causes all lights including brake lights and reverse lights to cycle on and …