Before you buy, check it isn't under a dangerous recall.

Insufficient design consideration in the routing of the air conditioning unit wire harness results in inadequate clearance between the harness and the microfilter housing cover fastening area. During microfilter replacement, the harness …

The rear wheel axle has insufficient strength design, causing excessive stress at the notched section. During operation, this can result in cracks in the rear axle, generating abnormal noise, and in worst …

Certain rear light LED drivers contain incorrect software due to improper manufacturing processes, rendering them incompatible with rear light control unit software. This can cause internal diagnostics during specific control conditions at …

The front axle steering control unit has insufficient design consideration for the lane-keeping assist function, which may result in reduced steering vibration of the lane departure warning during lane-keeping assist operation. As …

Due to inadequate manufacturing controls, the EV battery may experience internal cell short circuits at high charge levels. This may result in warning messages during driving, and in severe cases, may lead …

In modules within the high-voltage battery pack, the manufacturing process for electrode plates used in cells was improper, resulting in some modules with electrode plate debris adhered to them from the process. …

Improper securing of the main harness and power relay cord in the electrical wiring causes the angle sensor connector connected to the main harness to interfere with the fuel hose lock fitting. …

Insufficient assembly instructions for the cowl louver to the vehicle body have resulted in rainwater and similar substances dripping from the water-sealing section onto the brake booster. This causes rust to develop …

The CLU (Cluster Unit) control program has insufficient design consideration, which may cause the meter panel to restart and black out during driving. As a result, the speedometer and total mileage display …

The piston and top ring design in the engine is inadequate, resulting in excessive clearance between the piston and top ring. When the engine repeatedly decelerates from high RPM using engine braking, …

Wiring routed beneath the driver and passenger seats may not be properly configured due to inadequate manufacturing process. This can result in wiring damage during seat adjustment, causing the airbag warning light …

Pin links used in the travel hydraulic pump of the tire roller are subject to inadequate equipment management during machining, resulting in some units with insufficient strength due to machining defects. This …

The handlebar lock fastening bolt in the locking mechanism may have insufficient clamping force due to improper tightening method. Continued use could result in bolt loosening, preventing handlebar lock engagement when parked. …

Due to inadequate process control during cylinder boring, cylinder surfaces become rough. During operation, engine oil is drawn up into the combustion chamber and burned, increasing oil consumption. This causes poor lubrication, …

Certain studless tires for large trucks and buses have insufficient rubber bonding to steel materials positioned in the sidewall during manufacturing due to inadequate inspection equipment management, resulting in reduced rubber thickness …

In the high-voltage battery cell modules, improper manufacturing equipment settings have resulted in capacity imbalance between positive and negative electrodes in some cells. This can cause internal short circuits within the cell …

The brake pedal assembly may have insufficient welding of the rod connected to the brake system due to improper welding process. Continued use could cause the welded joint to separate, potentially resulting …

The electric power steering system has insufficient software design consideration in the steering gearbox control unit. When the steering moment sensor fails, the backup sensor does not transmit correct information to the …

Incorrect bracket specifications in air conditioning condenser replacement parts cause interference with surrounding wiring. Continued use in this condition may damage the wiring, potentially causing engine shutdown during operation and resulting in …

In replacement fuel tanks, improper welding of the internal baffle plate may cause the plate to detach due to vehicle vibration, potentially interfering with the fuel gauge float. This may result in …

The starter's starting relay has insufficient durability. Repeated engine starting and idle stop cycles cause abnormal contact wear, allowing wear debris to accumulate at the contact point. Continued use may result in …

The starter's starting relay has insufficient durability. Repeated engine starting and idle stop cycles cause abnormal contact wear, allowing wear particles to accumulate on the contact surfaces. Continued use may result in …

In small special-purpose vehicle forklifts: ① Design specifications for tail lights, brake lights, and reverse lights are inadequate, resulting in some vehicles exceeding 2.0 m in height lacking tail lights, brake lights, …

The driver assistance system control unit contains an improperly configured control program that may cause intermittent transmission loss of camera video signals. As a result, surround-view camera images may not display, preventing …

In the automatic transmission, insufficient review of the control program may prevent suppression of component over-rotation during malfunction. This can result in transmission damage and loss of driving capability. In the worst …

In the high-voltage battery cell modules, improper manufacturing equipment settings have resulted in unbalanced positive and negative electrode capacity in certain cells. This can cause internal short circuits within the cell module, …

Bolts fastening the upper oil pan and crankcase may not be tightened to specification due to improper manufacturing process. These bolts can loosen due to driving vibration and fall into the lower …

Steering tilt adjustment mechanism: Due to improper manufacturing processes, the durability of the nut push that secures the steering tilt is insufficient in some vehicles. Repeated position adjustments may result in loss …

Lane-keeping assist function: Due to improper control program in the meter cluster, when the function stops as a result of the driver removing their hands from the steering wheel, no warning sound …

In the engine control unit of manual transmission vehicles, improper energization control of the ignition coil can cause excessive current to flow through the ignition coil when the engine stalls due to …