Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 8 of 175
The Brake System Module (BSM) software has insufficient design consideration, which may cause communication faults with related ECUs due to bugs. As a result, multiple warning messages may appear on the instrument …
In the ABS (Anti-lock Braking System), due to improper manufacturing processes, the rear-wheel brake piping may not be correctly assembled. As a result, when the ABS and ESP (Electronic Stability Program) are …
The filter mesh in the passenger front airbag inflator has improper weave density due to inadequate manufacturing processes. During airbag deployment, internal pressure in the inflator increases, potentially rupturing the inflator container …
In the electric power steering system, insufficient maintenance of the connector processing equipment has resulted in some circuit board terminals not being properly inserted. Consequently, circuit disconnection may occur due to driving …
In brake lamp switches for excavators, loaders, and similar equipment, the positioning of the piston and microswitch relative to the diaphragm thickness (an internal component) is improperly adjusted. As a result, the …
Due to improper piston geometry in the brake master cylinder, the piston may not return to its normal position when disengaging the brake auto-hold function (※1) and hill-start assist function (※2), causing …
In the electric parking brake system, due to improper control programming, the parking brake may fail to engage when the key is turned off during rapid deceleration or before stopping, or when …
The intake pipe seal design is insufficient. Blowby condensate accumulating inside the intake pipe can leak from the connection between the intake pipe and turbocharger due to damage or deterioration, potentially dripping …
At the B terminal of the starter-generator, inadequate manufacturing control has resulted in some units where the B+ cable attachment nut is not tightened to the specified torque. Consequently, vibration during driving …
Some high-voltage battery cell modules have internal damage due to inadequate manufacturing control. During use, lithium may contact the positive electrode, causing conduction and short-circuiting. Continued operation could result in fire in …
The B-terminal of the starter-generator may have gaps between the sleeve and lead frame due to inadequate manufacturing control. This causes loose connections, increased resistance, abnormal overheating of the B-terminal, illumination of …
Some high-voltage batteries contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, which in worst case scenarios may result in thermal battery anomalies and lead to …
Trailer air hoses used when coupling with trailers may have insufficient strength due to improper manufacturing processes. Vibration during operation may cause damage to the service circuit (yellow hose), illuminating a warning …
Electrical devices mounted on the frame have inadequate paint specifications at the engine mounting point, resulting in unstable electrical connection with the battery negative terminal. Continued use may cause intermittent power loss …
The low-pressure fuel pump impeller (resin fan wheel) was insufficiently evaluated for swelling caused by fuel components, and the clearance between the impeller and pump case was inadequate. Consequently, the fuel-swollen impeller …
High-voltage battery cell modules may experience internal short circuits due to improper manufacturing. In the worst case, this could result in fire.
The Dynamic Stability Control unit has an inadequate program for detecting yaw-rate characteristic abnormalities, preventing correct judgment. Consequently, even if a yaw-rate characteristic abnormality occurs, it may not be detected as a …
The auxiliary battery voltage regulator in camper vehicles has insufficient design review, resulting in some units with excessive distance between the regulator output and fuse. Consequently, abnormal current may not be cut …
In the electric parking brake system, due to improper ECU programming, the ECU may fail to initialize when the start switch is turned on. This may cause warning lights to illuminate and …
The bolt hole drilling depth in the cable fastening section within the steering wheel was inappropriate, resulting in some units where the cable is not properly crimped when the bolt is tightened. …
Front-wheel brake hoses may have inadequate durability in high-temperature, high-humidity environments due to improper manufacturing processes. Additionally, some brake hoses have low flexibility in certain areas due to insufficient design review. Consequently, …
Trailer air hoses used for coupling with trailers may have insufficient strength due to improper manufacturing processes. Vibration during operation may damage the service circuit (yellow hose), causing the warning lamp to …
Takata airbag inflator may rupture, ejecting metal fragments
High-voltage battery cell modules may experience internal short circuits due to improper manufacturing. In worst-case scenarios, this may result in fire.
In the cell modules of the high-voltage battery of plug-in hybrid vehicles, improper equipment configuration results in uneven cell surfaces on some units. Consequently, internal short circuits can occur within the cell …
The turbocharger lubricating oil supply line has an improper fixing method. During rapid acceleration or heavy throttle application, internal oil pressure increases and stress concentrates on the oil seal. This causes the …
The rear suspension link rod has inadequate design standards, resulting in insufficient bushing interference strength. During use, the bushing interference loosens, causing noise. If use continues, the bushing may separate from the …
The control program for the driver-side LCD display (virtual cockpit) has insufficient design consideration. Due to vibrations during driving, internal cable resistance may increase, causing the display control program to incorrectly detect …
Due to improper assembly work instructions at the manufacturing plant, some drive shaft coupling bolts that transmit power from the gearbox are not tightened to the specified torque. This can cause the …
In the front suspension, improper assembly of the resin bearing causes the bearing to be shaved during nut tightening of the damper unit and damper mount. Bearing fragments become trapped between the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.