Before you buy, check it isn't under a dangerous recall.

Due to inadequate control programming in the engine control unit, when the urea SCR system malfunctions, the warning light fails to illuminate, resulting in non-compliance with safety standards.

Due to inadequate control software in the engine control unit, the particulate filter (DPF) regeneration interval does not occur at proper intervals, allowing excessive particulate matter to accumulate in the DPF. During …

Incorrect bracket specifications in air conditioning condenser replacement parts cause interference with surrounding wiring. Continued use in this condition may damage the wiring, potentially causing engine shutdown during operation and resulting in …

In replacement fuel tanks, improper welding of the internal baffle plate may cause the plate to detach due to vehicle vibration, potentially interfering with the fuel gauge float. This may result in …

The starter's starting relay has insufficient durability. Repeated engine starting and idle stop cycles cause abnormal contact wear, allowing wear debris to accumulate at the contact point. Continued use may result in …

The starter's starting relay has insufficient durability. Repeated engine starting and idle stop cycles cause abnormal contact wear, allowing wear particles to accumulate on the contact surfaces. Continued use may result in …

In small special-purpose vehicle forklifts: ① Design specifications for tail lights, brake lights, and reverse lights are inadequate, resulting in some vehicles exceeding 2.0 m in height lacking tail lights, brake lights, …

Due to inadequate component management in the transmission module, moisture has entered the electronic circuit board within the transmission module in some units. This may prevent the transmission position display signal from …

The driver assistance system control unit contains an improperly configured control program that may cause intermittent transmission loss of camera video signals. As a result, surround-view camera images may not display, preventing …

In the automatic transmission electrical wiring, improper routing design causes the wiring to contact and abrade against the front propeller shaft, resulting in damage. This leads to loss of electric motor power-assist …

Transmission control units contain incorrectly programmed control software due to improper manufacturing instructions. This causes the OBD system to malfunction, potentially resulting in exhaust emissions exceeding regulatory limits.

The engine control unit has an inappropriate control program that may cause misfires during catalyst warm-up heating mode. This causes the engine warning light (MIL) to illuminate and fuel injection to stop …

Due to inadequate component management of elements constituting the circuit board in the combination meter, incorrect parts were assembled in some units. When the affected element reaches high temperature during use, solder …

In the automatic transmission, insufficient review of the control program may prevent suppression of component over-rotation during malfunction. This can result in transmission damage and loss of driving capability. In the worst …

The wing power unit mounting bracket has inadequate strength due to improper welding control. Continued use in this condition may cause cracks to develop at the weld due to vibration during operation. …

In the rear combination lamp, due to improper work instructions, the desiccant inside the lamp is not properly affixed in some units. As a result, moisture-induced desiccant expansion may interfere with the …

Tires were improperly managed during production at the manufacturing facility, resulting in incorrect tires being installed. This causes non-compliance with safety standards.

In the electronically controlled air processing unit, inadequate evaluation during development can cause the silencer to detach during compressed air discharge from the air dryer. This may obstruct other traffic and cause …

Forklifts equipped with a special-order keypad have insufficient design consideration for password entry use as a starting device, resulting in keypad mounting position non-compliance with safety standards.

In the high-voltage battery cell modules, improper manufacturing equipment settings have resulted in unbalanced positive and negative electrode capacity in certain cells. This can cause internal short circuits within the cell module, …

Bolts fastening the upper oil pan and crankcase may not be tightened to specification due to improper manufacturing process. These bolts can loosen due to driving vibration and fall into the lower …

Steering tilt adjustment mechanism: Due to improper manufacturing processes, the durability of the nut push that secures the steering tilt is insufficient in some vehicles. Repeated position adjustments may result in loss …

The room lamp mounting brackets on excavator-loaders may be broken due to improper installation instructions. Vehicle vibration can cause the room lamp to detach, and contact between the lamp's metal parts and …

The covers installed on the left and right sides of the A-pillar as exterior trim have improper manufacturing processes, resulting in some units not being securely fastened with mounting clips. As a …

In the forward/reverse control solenoid valve (shuttle valve) of agricultural tractors, malfunction of the detection switch may occur due to the following conditions ①②, causing an error alarm and travel stoppage via …

Rear seat belt anchors may have insufficient attachment strength due to inadequate design consideration. Under impact loading during vehicle collision, the rear seat belt anchor may detach, failing to restrain occupants properly …

Lane-keeping assist function: Due to improper control program in the meter cluster, when the function stops as a result of the driver removing their hands from the steering wheel, no warning sound …

In the engine control unit of manual transmission vehicles, improper energization control of the ignition coil can cause excessive current to flow through the ignition coil when the engine stalls due to …

In the electric power steering system, improper assembly of harness connectors has resulted in some connectors not being correctly seated. Consequently, if connectors become disconnected due to driving vibration or similar conditions, …

In the intermediate shaft section between the engine and transmission of rotary snow-removal vehicles, improper manufacturing control has resulted in some units being fitted with non-genuine bearings. Consequently, grease leaks from the …