Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 3 of 175
The gas spring design that secures the steering post on the grader is insufficient. Gas may leak from inside the gas spring during tilt pedal operation. Continued use can reduce the gas …
The electric brake control module has insufficient design review, resulting in program defects. When the parking brake is activated while the electric parking brake system is malfunctioning, the red warning light does …
In the detachable portable battery installed in electric two-wheelers, improper exterior processing control of battery cells and inappropriate outer diameter settings of the electrode layer cause cracks to develop in the cell …
In the non-driven rear-rear axle hub assembly, the evaluation of lock washer wear was insufficient. Worn lock washers may disengage due to vehicle vibration, etc., interfere with the hub cover, and cause …
The electric power steering control unit has insufficiently designed control software. When internal components of the electric power steering motor reach high temperatures, the fault detection system may misidentify mechanical vibration of …
The rear axle cross member may have been welded with misaligned components due to inadequate manufacturing processes. Cracks can initiate at the welded joint of the rear axle cross member. Continued use …
The rear lighting fixtures (tail lights, brake lights, reverse lights, turn signal indicators) and rear reflectors of the semi-trailer may not conform to safety standards regarding geometric visibility due to insufficient design …
In recall work (notification number 5485 dated May 30, 2024), due to inadequate documentation in the drive motor replacement work instructions, some front suspension member front-side fixing bolts were tightened beyond the …
The low-pressure fuel pump impeller (plastic fan wheel) material selection was inadequately evaluated. The impeller may swell and deform due to fuel exposure, causing it to contact the pump casing and result …
Insufficient design consideration in the routing of the air conditioning unit wire harness results in inadequate clearance between the harness and the microfilter housing cover fastening area. During microfilter replacement, the harness …
The rear wheel axle has insufficient strength design, causing excessive stress at the notched section. During operation, this can result in cracks in the rear axle, generating abnormal noise, and in worst …
Certain rear light LED drivers contain incorrect software due to improper manufacturing processes, rendering them incompatible with rear light control unit software. This can cause internal diagnostics during specific control conditions at …
The front axle steering control unit has insufficient design consideration for the lane-keeping assist function, which may result in reduced steering vibration of the lane departure warning during lane-keeping assist operation. As …
Due to inadequate manufacturing controls, the EV battery may experience internal cell short circuits at high charge levels. This may result in warning messages during driving, and in severe cases, may lead …
In modules within the high-voltage battery pack, the manufacturing process for electrode plates used in cells was improper, resulting in some modules with electrode plate debris adhered to them from the process. …
Improper securing of the main harness and power relay cord in the electrical wiring causes the angle sensor connector connected to the main harness to interfere with the fuel hose lock fitting. …
Insufficient assembly instructions for the cowl louver to the vehicle body have resulted in rainwater and similar substances dripping from the water-sealing section onto the brake booster. This causes rust to develop …
The CLU (Cluster Unit) control program has insufficient design consideration, which may cause the meter panel to restart and black out during driving. As a result, the speedometer and total mileage display …
The piston and top ring design in the engine is inadequate, resulting in excessive clearance between the piston and top ring. When the engine repeatedly decelerates from high RPM using engine braking, …
Wiring routed beneath the driver and passenger seats may not be properly configured due to inadequate manufacturing process. This can result in wiring damage during seat adjustment, causing the airbag warning light …
Pin links used in the travel hydraulic pump of the tire roller are subject to inadequate equipment management during machining, resulting in some units with insufficient strength due to machining defects. This …
The handlebar lock fastening bolt in the locking mechanism may have insufficient clamping force due to improper tightening method. Continued use could result in bolt loosening, preventing handlebar lock engagement when parked. …
Due to inadequate process control during cylinder boring, cylinder surfaces become rough. During operation, engine oil is drawn up into the combustion chamber and burned, increasing oil consumption. This causes poor lubrication, …
Certain studless tires for large trucks and buses have insufficient rubber bonding to steel materials positioned in the sidewall during manufacturing due to inadequate inspection equipment management, resulting in reduced rubber thickness …
In the high-voltage battery cell modules, improper manufacturing equipment settings have resulted in capacity imbalance between positive and negative electrodes in some cells. This can cause internal short circuits within the cell …
The brake pedal assembly may have insufficient welding of the rod connected to the brake system due to improper welding process. Continued use could cause the welded joint to separate, potentially resulting …
The electric power steering system has insufficient software design consideration in the steering gearbox control unit. When the steering moment sensor fails, the backup sensor does not transmit correct information to the …
Incorrect bracket specifications in air conditioning condenser replacement parts cause interference with surrounding wiring. Continued use in this condition may damage the wiring, potentially causing engine shutdown during operation and resulting in …
In replacement fuel tanks, improper welding of the internal baffle plate may cause the plate to detach due to vehicle vibration, potentially interfering with the fuel gauge float. This may result in …
The starter's starting relay has insufficient durability. Repeated engine starting and idle stop cycles cause abnormal contact wear, allowing wear debris to accumulate at the contact point. Continued use may result in …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.