Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 50 of 175
In the engine compartment, the routing of the right front brake pipe is improper, causing it to interfere with the engine coolant hose retaining band due to driving vibrations and other factors. …
In the driver-side SRS airbag inflator, the desiccant was assembled in a moisture-saturated state during manufacturing. Repeated environmental temperature changes cause the gas generant to degrade. During airbag deployment, internal pressure in …
In the driver-side SRS airbag inflator, the desiccant was assembled in a moisture-saturated state during manufacturing. Repeated environmental temperature changes can cause degradation of the gas generant. This may result in abnormal …
In pole tractor specification vehicles with large frames, the brake system modification for installing an additional air supply port (coupling) for pole trailers is improper, resulting in insufficient compressed air capacity in …
The passenger-side airbag inflator lacks adequate moisture protection for the gas generator. Repeated temperature and humidity cycling can degrade the gas generator, potentially causing inflator container rupture during airbag deployment.
(1) In the electric power steering control unit, due to inappropriate control programming, a warning may not be issued when the driver releases the steering wheel during operation of the driving support …
(1) In the electric power steering control unit, due to inappropriate control programming, a warning may not be issued when the driver removes their hands from the steering wheel while the driver …
The passenger-seat airbag inflator lacks adequate moisture protection for its gas-generant. When subjected to repeated large temperature fluctuations in high-humidity environments, the gas-generant may deteriorate. Consequently, the inflator container may rupture during …
In the ASCM (Advanced Safety Control Module) that controls front seat belt tension for right-hand drive vehicles, improper manufacturing instructions have resulted in the connector pin configuration of the connected wire harness …
The driver-side airbag inflator may have inadequate moisture protection for the gas generant. When exposed to repeated temperature fluctuations in high-humidity environments, the gas generant can degrade. This may cause the inflator …
The driver-side airbag inflator may have inadequate moisture protection on its gas generant. Repeated temperature cycling in high-humidity environments can cause degradation of the gas generant, potentially resulting in inflator container rupture …
Mounting nuts for left and right tail lights have insufficient cleaning, leaving residue. This residue can cause damage to the tail light mounting area, and in the worst case, the tail light …
In the ABS (Anti-lock Braking System) modulator, improper assembly fixture geometry of component parts can generate aluminum particles during assembly. When the ABS operates, these aluminum particles may become lodged in the …
On large trucks and buses equipped with air suspension, improper spring setting securing the rear brake shoes causes the shoes to vibrate during operation when subjected to vibration input, striking the clip …
In the parking brake circuit of agricultural tractors, ①air hose durability is insufficient, causing cracks in the air hose. This results in air leakage from the hose, which may prevent the parking …
In the parking brake circuit of agricultural tractors, ① air hose durability is insufficient, causing air hoses to develop cracks. This allows air to leak from the hose, preventing the parking brake …
In the fuel evaporative emission control system, the vapor separator—which separates evaporated fuel into liquid and gas phases—has inadequate bonding at its joints in some units, resulting in insufficient joint strength. Continued …
The panoramic sliding roof interior lighting has an inadequately designed electrical circuit fuse. If the sliding roof drain becomes blocked by external factors, water may infiltrate the interior lighting module circuit, causing …
In the parking brake system, due to inadequate assembly work instructions, the connection between the brake lever and brake cable lacks a lock-nut. Consequently, vibration during operation may loosen this connection, increasing …
The brake light switch uses an inappropriate contact design. Silicone gas volatilized from vehicle interior cleaning products and cosmetics can form an insulating film on the contact surfaces, resulting in poor electrical …
On large buses, an improperly selected fuse is used in the optional front door glass heater circuit. The fuse holder may melt due to elevated temperature at the fuse terminal connections. Continued …
In small buses, a label indicating the type of brake fluid is not affixed because there is no instruction to attach the label.
In the braking system of wheel cranes, brake pipe fittings with improper dimensions have been tightened to insufficient threading depth. Continued use in this condition may result in brake fluid leakage from …
In wheel crane fuel tanks, the mounting bolts of the fuel pump configured as an optional component have improper dimensions, causing the bolt tips to contact the top surface of the fuel …
The Electronic Stability Program (ESP) control unit has an inadequate control program, which may prevent the ESP from activating after engine start. If the ESP does not activate, the electronic parking brake …
The hydraulic ABS unit's assembly fixture geometry is inappropriate, which can generate aluminum particles during assembly. When the ABS activates, these aluminum particles may become lodged in the check valve, potentially locking …
In the combination meter, the fuel gauge circuit has an inadequate design. Repeated thermal expansion of the circuit board inside the meter, caused by heat generated from resistance elements in the circuit …
The brake vacuum electric pump, which generates negative pressure in the brake booster, has an incorrect bearing installed on the main shaft, risking premature bearing seizure. This may cause the brake vacuum …
1) Improper installation of the fuel pump inside the fuel tank may cause the level sensor to interfere with the feed line. This prevents accurate measurement of fuel level, resulting in the …
1) Improper installation of the fuel pump inside the fuel tank can cause the level sensor to interfere with the feed line, preventing accurate fuel level measurement. The fuel gauge may display …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.