Before you buy, check it isn't under a dangerous recall.

Due to inadequate manufacturing control of the steering coupling, the bolts securing the steering coupling may not be properly tightened. As a result, these bolts may loosen and detach during use, causing …

Due to inadequate manufacturing control, a gap may exist between the sleeve and lead frame at the B terminal of the starter-generator. This causes loose connections, increased resistance, abnormal overheating of the …

In the collision mitigation brake system, the control program design embedded in the front camera is insufficient. When specific operations are performed, even if a forward collision hazard is detected, the warning …

The ESP (Electronic Stability Program) module control software has insufficient design review, causing erroneous DTC (fault code) detection at engine startup, which illuminates the brake warning light and disables the vacuum pump. …

Certain fuel system injectors have insufficient component strength due to improper molding during the injector body manufacturing process. Repeated high-load operation can cause cracks in the injector, leading to fuel leakage into …

The airbag ECU event data recorder software has insufficient design review, which may result in steering correction function data not being recorded. Consequently, when collision data is retrieved after an accident, steering …

Certain fuel pipes have insufficient holding force due to improper management values for bracket retention. Repeated high-RPM engine operation during circuit driving causes the fuel pipe to resonate from vibration, resulting in …

Takata airbag inflator may rupture, ejecting metal fragments

Gasoline may overflow in large quantities from the fuel tank filler neck during refueling. Vaporized gasoline can be drawn into the radiator by the engine cooling fan. If the radiator is at …

Takata airbag inflator may rupture, ejecting metal fragments

The event data recorder program is inappropriate, causing failure to correctly record vehicle stability control system and traction control system information when a collision occurs in specific driving modes with vehicle stability …

The brake hose installed between the brake fluid reservoir tank and brake master cylinder may have been assembled with an incorrect part due to improper manufacturing instructions. During use, the brake fluid …

On agricultural tractor trailer brake compressed air hoses, insufficient design consideration may cause interference with the fuel tank. Continued use may result in hose wear and damage, causing air leakage, and in …

In the electrical wiring, terminal crimps between the left-hand switch harness wires are improperly crimped. Repeated harness sliding caused by steering wheel operation can wear the crimped section. Continued use may cause …

Due to inadequate fixture management during painting of the front brake panel prior to installing the speedometer cable, paint adheres to the cable insertion hole, reducing its diameter in some cases. When …

In the hydraulic lines for the rear spoiler, the lock pin is not properly installed due to inadequate manufacturing process. As a result, the lock pin may disengage due to vibration during …

Fuel pipe attachment nuts and injector rail attachment bolts in the engine compartment have been tightened with insufficient torque due to improper torque specification setting. During use, vibration may cause the fuel …

Takata airbag inflator may rupture, ejecting metal fragments; driver airbag

The snap rings securing the covers at the top of the front left and right air suspension units have incomplete installation due to improper manufacturing processes, resulting in covers that are not …

Takata airbag inflator may rupture, ejecting metal fragments; driver airbag

Takata airbag inflator may rupture, ejecting metal fragments; driver airbag

Chemical — The brake pads contain asbestos fibres. Asbestos causes cancer. The product does not comply with the REACH Regulation.

Chemical — The product contains asbestos fibres. Asbestos causes cancer. The product does not comply with the REACH Regulation.

Chemical — The brake pads contain asbestos fibres. Asbestos causes cancer. The product does not comply with the REACH Regulation.

Takata airbag inflator may rupture, ejecting metal fragments; driver airbag

The transmission control module software has insufficient design consideration, which may result in improper control under certain conditions. In the worst case, wheel lock may occur while driving.

In the rear-wheel braking system, improper component management during manufacturing resulted in brake caliper assemblies of different models being installed on some vehicles. As a result, the brake pads cannot properly contact …

Takata airbag inflator may rupture, ejecting metal fragments; passenger airbag

Takata airbag inflator may rupture, ejecting metal fragments; driver airbag

In the starter electrical wiring, design review of cable routing tolerances was insufficient, resulting in interference with the crossmember edge in some vehicles. Continued use may cause the wiring insulation to be …