Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 16 of 355
Due to inadequate parts management for in-factory repair, an incorrect fuel pump was installed. This causes the fuel level gauge sender to snag on internal fuel tank components, resulting in incorrect fuel …
During service of the low-pressure fuel pump, improper packaging of service parts resulted in shipment of non-genuine seals. When these non-genuine seals are installed during service, the seal between the fuel pump …
In the Automatic Gearbox Shifter Module (AGSM), insufficient design review can cause signal misalignment in the two internal signals when the edge of the Park Position switch on the center console is …
In the braking system, the heat shield tube of the rear brake hose connecting the ABS control unit and rear brake caliper may not be installed correctly. As a result, radiant heat …
The Brake System Module (BSM) software has insufficient design consideration, which may cause communication faults with related ECUs due to bugs. As a result, multiple warning messages may appear on the instrument …
Polycarbonate tailgates may have insufficient adhesive application due to improper manufacturing process. As a result, when driving at high speed (approximately 154 km/h or higher) with the window open, the tailgate may …
In the ABS (Anti-lock Braking System), due to improper manufacturing processes, the rear-wheel brake piping may not be correctly assembled. As a result, when the ABS and ESP (Electronic Stability Program) are …
The filter mesh in the passenger front airbag inflator has improper weave density due to inadequate manufacturing processes. During airbag deployment, internal pressure in the inflator increases, potentially rupturing the inflator container …
In the electric power steering system, insufficient maintenance of the connector processing equipment has resulted in some circuit board terminals not being properly inserted. Consequently, circuit disconnection may occur due to driving …
The left and right front end bolts connecting the side members and bumper reinforcement were not tightened to the specified torque due to improper manufacturing processes. Continued use may result in bolt …
The left rear side member may contain cracks due to improper manufacturing processes. Continued use may cause cracks to propagate under driving vibration and similar stresses, resulting in insufficient strength and non-compliance …
In rear fog lights, improper manufacturing of the bulb socket may prevent proper contact connection. As a result, the rear fog light may not illuminate, potentially causing non-compliance with safety standards.
In brake lamp switches for excavators, loaders, and similar equipment, the positioning of the piston and microswitch relative to the diaphragm thickness (an internal component) is improperly adjusted. As a result, the …
Due to improper piston geometry in the brake master cylinder, the piston may not return to its normal position when disengaging the brake auto-hold function (※1) and hill-start assist function (※2), causing …
The front leaf spring in the front suspension was insufficiently designed. When used in high center-of-gravity or heavy-load configurations, the spring lacks adequate strength under roll input. Continued operation risks leaf spring …
In the electric parking brake system, due to improper control programming, the parking brake may fail to engage when the key is turned off during rapid deceleration or before stopping, or when …
In the water pump, improper maintenance of the manufacturing equipment has resulted in some units where the pulley is inserted at an angle to the shaft. As a result, during use the …
In the power transmission system, improper management of clutch plates allows rust-preventive oil residue on the clutch plate to mix with friction material wear particles from the friction plate. When heat is …
Some front active stabilizer bars have insufficient hardening due to improper manufacturing processes. Additionally, some units exhibit localized corrosion due to inadequate corrosion prevention treatment. Vibration during operation may cause internal cracks, …
The intake pipe seal design is insufficient. Blowby condensate accumulating inside the intake pipe can leak from the connection between the intake pipe and turbocharger due to damage or deterioration, potentially dripping …
At the B terminal of the starter-generator, inadequate manufacturing control has resulted in some units where the B+ cable attachment nut is not tightened to the specified torque. Consequently, vibration during driving …
Some high-voltage battery cell modules have internal damage due to inadequate manufacturing control. During use, lithium may contact the positive electrode, causing conduction and short-circuiting. Continued operation could result in fire in …
The B-terminal of the starter-generator may have gaps between the sleeve and lead frame due to inadequate manufacturing control. This causes loose connections, increased resistance, abnormal overheating of the B-terminal, illumination of …
On the lateral rod and stabilizer bracket, improper welding instructions resulted in the internal plate being tack-welded rather than fully welded. Continued use in this condition may cause cracking in the bracket.
Some high-voltage batteries contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, which in worst case scenarios may result in thermal battery anomalies and lead to …
Road rollers lack a maximum load capacity display on the rear of the vehicle body because there was no awareness that such a marking was necessary for the water/emulsion tank load capacity. …
In the warning horn of the road roller, due to insufficient examination of the mounting position, the sound volume is lower than the specified loudness and does not conform to safety standards.
Trailer air hoses used when coupling with trailers may have insufficient strength due to improper manufacturing processes. Vibration during operation may cause damage to the service circuit (yellow hose), illuminating a warning …
The control unit for traffic information has insufficient program design review, which may result in delayed detection of obstacles ahead. Therefore, it does not comply with Regulation 159.
The speedometer and odometer cases lack sufficient water resistance, allowing rainwater and moisture to enter the interior. Continued use may result in circuit board corrosion, rendering speed and distance displays inoperative.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.