Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10558 recalls on record · page 14 of 352
The control unit for traffic information has insufficient program design review, which may result in delayed detection of obstacles ahead. Therefore, it does not comply with Regulation 159.
The speedometer and odometer cases lack sufficient water resistance, allowing rainwater and moisture to enter the interior. Continued use may result in circuit board corrosion, rendering speed and distance displays inoperative.
Electrical devices mounted on the frame have inadequate paint specifications at the engine mounting point, resulting in unstable electrical connection with the battery negative terminal. Continued use may cause intermittent power loss …
In the evaporative emission control system, the air-fuel ratio sensor harness is improperly secured, causing interference with the drive chain in some vehicles. If the harness insulation is damaged due to this …
Sealing bolts installed in the engine lower case have improperly formed threads due to inadequate inspection fixture management and molding procedures, resulting in degraded sealing performance when tightened. Continued use may cause …
The navigation system control program is defective, which may cause failure to start or repeated restarts during operation. As a result, the LCD screen may not display camera footage during forward/left confirmation …
The low-pressure fuel pump impeller (resin fan wheel) was insufficiently evaluated for swelling caused by fuel components, and the clearance between the impeller and pump case was inadequate. Consequently, the fuel-swollen impeller …
In the integrated lighting unit mounted on the rear of the van-type truck, the installation position's standard compliance was not verified during design. As a result, the rear light illumination portion is …
High-voltage battery cell modules may experience internal short circuits due to improper manufacturing. In the worst case, this could result in fire.
In the engine's fuel injection system, the plating process of the injector rail is inadequate, which may cause the plating to peel off during use. Peeled plating particles can clog the injector, …
Certain carbon wheels have insufficient bolt guide strength due to inadequate design review. Running vibration can cause cracks in the affected component, and continued use may result in component failure, bolt loosening, …
In the automatic emergency call system, due to an inappropriate control program in the telematics control unit, if the connection is lost while out of service area during an active call, it …
The console cover on excavator-loaders (canopy specification) has insufficient waterproof design considerations, allowing rainwater and wash water to infiltrate the console interior. Continued operation may result in water entering the junction connector …
The Dynamic Stability Control unit has an inadequate program for detecting yaw-rate characteristic abnormalities, preventing correct judgment. Consequently, even if a yaw-rate characteristic abnormality occurs, it may not be detected as a …
Certain vehicles equipped with asphalt emulsion spraying functionality have insufficient chassis frame strength. As a result, they may not comply with safety standards.
The auxiliary battery voltage regulator in camper vehicles has insufficient design review, resulting in some units with excessive distance between the regulator output and fuse. Consequently, abnormal current may not be cut …
On certain vehicles, the backup light and rear fog light mounted on the rear bumper have non-specification parts installed due to improper manufacturing process procedures. As a result, these do not comply …
In the electric parking brake system, due to improper ECU programming, the ECU may fail to initialize when the start switch is turned on. This may cause warning lights to illuminate and …
The onboard diagnostic system's diagnostic program in the DME (electronic control unit that oversees the entire engine control system) has insufficient design consideration. When abnormalities related to the variable valve mechanism (Valvetronic) …
The bolt hole drilling depth in the cable fastening section within the steering wheel was inappropriate, resulting in some units where the cable is not properly crimped when the bolt is tightened. …
In the high-voltage circuit system, improper design of the high-voltage relay (sub-junction box) causes abnormal heating of connector terminals, potentially resulting in terminal fusion. This may cause insulation resistance to decrease, illuminating …
The upholstery materials on the right side of the driver seat backrest and the left side of the passenger seat backrest employ inadequate facing material selection, resulting in flame spread at a …
The control program for the high-voltage starter-alternator has insufficient design review, which may cause the system's monitoring function to incorrectly detect a fault and stop operation. This results in increased exhaust emissions …
Front-wheel brake hoses may have inadequate durability in high-temperature, high-humidity environments due to improper manufacturing processes. Additionally, some brake hoses have low flexibility in certain areas due to insufficient design review. Consequently, …
In welfare vehicles equipped with manual driving controls, the return spring for the accelerator ring may have improper spring load, causing the accelerator ring to fail to return. This may result in …
The rear-view camera for rear-view confirmation has insufficient waterproof design consideration. When pressurized water is applied to the rear camera during washing, water may penetrate into the camera's interior. This can cause …
The EPIC (Electric Power Inverter Converter Control Module) program has insufficient design consideration, which may prevent transition to sleep mode after engine shutdown. Consequently, after engine shutdown, communication with linked modules may …
In the wiring of the lumbar seat belt pretensioners located beneath the driver and front passenger seats, improper work instructions have resulted in some vehicles using incorrect clips to secure the wiring. …
In the sub-engine control unit of road rollers, due to insufficient design review, the automatic restart inhibit lamp may illuminate after fault diagnosis, preventing automatic restart.
The onboard diagnostic program of the DME (electronic control unit governing the entire engine control system) has insufficient design review. When abnormalities related to the variable valve mechanism (Valvetronic) are detected, diagnostic …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.