Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 109 of 175
In the engine compartment, insufficient clearance between the fuel pipe and cooling hose clamp may cause the fuel pipe to interfere with the clamp due to vibration during driving. This may result …
The gas generant assembly process in the passenger-side airbag inflator is improper, resulting in insufficient gas generant charge in some units. Vehicle vibrations may cause the gas generant to become powdered, and …
The gas generator assembly work within the passenger airbag inflator is improper, resulting in insufficient gas generator charge in some units. Consequently, vehicle vibration causes the gas generator to become powdered; when …
The gas generant assembly work within the passenger-side airbag inflator is performed improperly, resulting in insufficient gas generant charge in some units. Consequently, vehicle vibration causes the gas generant to become powdery, …
Due to improper programming in the electric control automatic parking brake control unit, if power supply to the ABS control unit and injection control unit is interrupted due to electrical wiring contact …
The electronic control circuit for the washer fluid freeze-protection heater has insufficient protective function, which may cause the printed circuit board to overheat. As a result, the washer fluid piping within the …
Insufficient protection in the electronic circuit controlling the washer fluid freeze-protection heater may cause the printed circuit board to overheat. This can result in damage to the washer fluid lines within the …
The flat cable of the steering roll connector may develop chemical stress cracks on its surface due to manufacturing variations in the grease applied to the cable during production. Continued use of …
On large trucks, if fuel filter replacement and fuel tank cleaning are not performed at regular intervals, impurities accumulate in the fuel. This causes wear on the injector seat, increasing fuel injection …
Inadequate clearance between the brake hose bracket mounting bolt and the rear left tire; on high-center-of-gravity vehicles performing sharp turns or similar maneuvers, the bolt may contact the tire sidewall.
① In the horn switch wiring, improper cable routing can cause the wiring to break due to repeated steering operations. As a result, the horn may fail to sound.
The fastening torque of the bolts securing the rear suspension to the frame is insufficient. Repeated lifting and moving of the vehicle bed during parking causes the bolts to loosen, and they …
On rear tandem axle heavy-duty trucks, improper welding of the rear non-drive axle housing may result in cracks at the weld. Continued operation in this condition may lead to axle housing fracture, …
The sleeve design on the front brake hose is inadequate, allowing deicing salts and similar substances to accumulate within the sleeve and causing corrosion of the hose's metal fittings. Continued use in …
The check valve installed in the vacuum line of the brake booster is made of inappropriate material, causing poor sealing. This allows atomized engine oil from the vacuum pump to enter the …
The material of the outer resin portion of the tensioner pulley, which adjusts the tension of the power steering pump drive belt, is inadequate. This resin portion may fracture, resulting in abnormal …
The welding of the stopper plate that regulates steering angle to the frame's head pipe was performed improperly, resulting in insufficient weld penetration in some units. Repeated impacts from steering input during …
The brake light switch contacts have insufficient electrical load capacity. Repeated brake operation causes contact wear, resulting in brake light failure. This may prevent the shift lever from moving out of the …
Improper molding of the rear brake light switch case causes the internal movable contact to remain beyond its operating range, resulting in the brake light staying continuously illuminated. Continued use in this …
The clip retaining the speedometer cable is insufficiently crimped, and cannot maintain cable retention during suspension compression and extension. The cable may slip out of the clip, and when the steering wheel …
Improper welding between the fuel tank bottom and fuel pump mounting plate may result in insufficient attachment strength. Fuel sloshing from vibration during driving can cause the weld to separate, potentially leading …
Improper machining of the worm shaft oil passage hole within the power steering gearbox. Repeated low-speed turning and stationary steering operations may result in excessive steering effort.
The piston seal installed inside the steering cylinder of the forklift steering device has insufficient strength and may wear prematurely. Continued operation in this condition can result in oil leakage inside the …
During the manufacturing process of fuel pressure pipes routed under the vehicle body, protrusions may form inside the pipe. This results in poor sealing at the connection between the pipe and quick-release …
Due to inadequate control programming in the Variable Gear Ratio Steering System (VGRS), rapid steering wheel return operations following normal stationary turning can cause the steering wheel neutral position to temporarily deviate …
The upper arm of the front wheel suspension has improper position control during welding of two sheet metal plates, resulting in misalignment of the ball joint mounting hole position on some units. …
The solder temperature of the operation switches on both sides of the steering wheel is inappropriate, which may cause wiring fractures on the switch circuit board. As a result, the operation switches …
In LPG-specification engine forklifts, improper bending during LPG pipe manufacturing may cause wrinkling at the bend point. Continued use in this condition can result in LPG pipe damage due to engine vibration, …
The write program for configuration data in the vehicle control computer is inappropriate. Upon charging plug insertion, the set value for deceleration force during plugging braking (deceleration by switching between forward/reverse without …
The fastening bolts at the fixed portion (support joint cover) of the steering joint connecting the steering wheel and power steering unit are insufficiently tightened in some units. Continued operation may cause …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.