Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 13 of 175
On grader steering posts, improper assembly instructions for internal gas spring components resulted in push valves and brackets being assembled in contact with each other. Operating vibrations may depress the push valve, …
In the electrical wiring of the work implement on agricultural tractors, insufficient design consideration has resulted in oversized protection fuses for the PTO switch and PTO brake solenoid valve. When high current …
In the semi-trailer electric steering system, due to improper design of the control program in the control unit, the electromagnetic valve fault monitoring function may activate if power is temporarily cut during …
In 12V and 48V ground wiring located in the engine compartment and undercarriage, improper assembly at manufacturing has resulted in cases where the nut at the body ground terminal point is not …
Fuel hoses may experience accelerated degradation due to heat as a result of inappropriate material selection. This can result in reduced sealing integrity at connection points, potentially leading to fuel leakage.
The oil filter case material used in the oil filter, which filters lubricating oil for the engine, differs from specification. Consequently, the case may rupture under internal pressure of the lubricating oil, …
Manufacturing tolerances in the instrument panel opening, which is the airbag deployment path of the passenger seat airbag inflator, may result in unintended deployment. Consequently, the passenger seat airbag may not fully …
In hybrid vehicles, the brake actuator control computer may have insufficient control program design, resulting in inability to properly regulate brake hydraulic pressure during cornering braking. Consequently, temporary loss of intended braking …
In the in-tank fuel pump unit, improper selection of impeller material can cause impeller deformation when fuel temperature rises, and improper manufacturing processes can introduce foreign matter into the pump operating section. …
In the wiring routing to the refrigeration unit condenser, improper cable routing causes interference with the fuel hose due to driving vibration and other factors. Continued use in this condition may result …
The aluminum bracket (stay) attached to the master cylinder on the front brake fluid reservoir tank has insufficient strength. Due to vibration during operation, the stay may bend and, in the worst …
Front and rear suspension trailing arms have insufficient corrosion resistance due to inadequate corrosion evaluation during material selection. Continued use over extended periods causes corrosion and cracking at the arm joint, resulting …
The waterproof structure of the front and rear wheel speed sensors is inadequate. Water may seep into the sensor during driving in rain and similar conditions. This causes sensor circuit short circuits …
In shovel loader final drives (reduction gears), insufficient design specifications result in inadequate bolt torque on the ring gear fasteners. Continued operation in this condition can cause bolts to loosen, leading to …
Roof panels affixed to the body with adhesive may have been repaired with improper work instructions, resulting in inadequate adhesive strength. Continued separation due to aerodynamic forces during operation could result in …
In the pre-fuse box located in the front passenger footwell, improper assembly during manufacturing results in the power supply wiring attachment nut not being tightened to the specified torque. Consequently, vibration during …
In the high-voltage battery management system, due to improper control programming, concentrated data requests from other control units can cause memory overload, triggering a reset that may inadvertently open the battery contactor. …
Transmission electrical wiring has inadequate cable routing design, causing excessive stress on connector wire seal sections and deforming them. This compromises seal integrity, allowing rainwater ingress into connectors and causing short circuits. …
Improper manufacturing control of the passenger-side airbag has resulted in some units with improperly assembled airbag covers. When the passenger-side airbag deploys, depending on the cover attachment position, occupant protection may not …
The shift cable for the transmission parking lock mechanism may have a damaged sleeve or improperly installed retaining clip due to inadequate work instructions during manufacturing. This can result in the parking …
The braking system has inadequate design, resulting in insufficient front brake hose length. Continued use in this condition causes excessive load on the brake hose ends due to steering angle, leading to …
The brake system has an improper design resulting in insufficient length of front brake hoses. Continued use in this condition causes excessive stress on brake hose ends due to steering angle, leading …
In medium-duty trucks, insufficient design review of wiring routing tolerances has resulted in interference between wiring on the left frame and peripheral components such as the engine side cover. Continued use may …
The turbocharger lubricating oil supply line has inadequate fastening. During rapid acceleration, internal oil pressure increases, causing stress concentration on the oil seal. This can lead to oil seal degradation and oil …
In the transmission control computer, clutch control during deceleration is improper. When braking firmly to a stop, the clutch connecting the engine and motor may remain disengaged. As a result, power from …
On vehicles equipped with dual-axle leaf suspension at the rear, reaction rod fixing bolts are not tightened to the specified torque due to insufficient tool management controls during fastening. Consequently, bolts may …
The hydraulic motor that maintains the position of the operator cabin on the forklift loader may slip due to air or contaminants entering the hydraulic circuit. As a result, the cabin may …
In the fuel system, the fuel pressure/temperature sensor mounting housing attached to the fuel supply pipe has inadequate manufacturing control, resulting in insufficient housing strength in some units. During use, cracks may …
Certain drive batteries in PHEV-specification vehicles have internal defects in battery cells, which may result in vehicle fire.
In two-axle couplers for large tractors, the lock guard (misconnection prevention component) shape was changed during design revision for manufacturing process improvement. Due to improper shape, when coupling operations are performed with …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.