Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 46 of 175
Due to improper programming of the transmission control module, the clutch that switches gear stages in the automatic transmission may not operate correctly. As a result, during driving, the transmission may fail …
The occupant protection system impact sensors contain insufficient solder joint strength on internal circuit boards due to inadequate maintenance of manufacturing equipment. During use, cracks may develop in the solder joints, causing …
The rear suspension torque link buffer device may have insufficient weld strength due to inadequate strength design considerations. Metal fatigue and similar issues during use may cause weld fracture, potentially resulting in …
Wheel cranes have incorrect material filter heads installed in the hydraulic fluid line filters, resulting in insufficient strength in some units. This can cause line filter damage and hydraulic fluid leakage. In …
Interior pillar covers may not be securely fixed to pillars due to improper installation instructions at the time of manufacture. Consequently, if a side airbag deploys during a collision or similar event, …
The evaporator drain hose in the air conditioning system may be improperly installed, causing condensation to leak into the passenger compartment. This can lead to water accumulation beneath the vehicle, resulting in …
The plastic cover inside the fender may have improper mounting settings, causing looseness at the attachment points. Due to vibrations during driving, the attachment bolts may loosen, and in the worst case, …
The plastic cover inside the fender has improper mounting settings, which can cause looseness at the attachment points. As a result, mounting bolts may loosen due to driving vibration and other factors, …
In diesel vehicle fuel injection systems, the fuel pipe connecting the fuel pump and common rail has improper torque specification instructions. Due to assembly variation of this pipe, the fastened joint may …
In four-wheel drive vehicles, the rear axle differential oil seal is made of improper material, causing abnormal wear of the seal lip under low-temperature conditions. This may result in differential oil leakage, …
Due to inadequate parts management in the fuel system, the high-pressure pump protective plate is not installed. If the high-pressure pump is damaged in a collision, fuel may leak, potentially resulting in …
The battery positive cable connecting the power distribution box and battery, which supplies power to vehicle electrical components, has improper plating and structure in the connector contact area. Corrosion caused by vehicle …
The front brake master cylinder design is inadequate, resulting in some units with insufficient brake lever play. Consequently, the brake may gradually engage even when the brake lever is not operated.
On agricultural tractors, certain parking brake systems have improperly set air pressure in the overflow valve, resulting in insufficient air pressure to release the parking brake. Consequently, the parking brake may not …
In the steering knuckle of crane carrier vehicles, improper casting drawing specifications result in insufficient thickness in the upper portion of the knuckle. Prolonged use may cause cracks to develop in the …
In hybrid vehicle fuel pumps, the voltage applied to the pump is high and motor brush assembly is improper, causing the brush to tilt and generate excessive sparking, resulting in abnormal wear. …
Due to improper routing of the engine harness, the engine harness and link pipe heat shield contact each other on some vehicles. This contact causes engine harness damage from vehicle vibration, resulting …
The PTC heater auxiliary heating harness has an inappropriately sized wire diameter. When the PTC heater operates continuously at maximum output, heat generation can cause connector terminal deformation. Continued use in this …
In the electric power steering system, improper routing of electrical wiring has resulted in some units where the wiring is pinched between the suspension frame and underpanel. Due to vibration during driving, …
In the brake pedal of the shovel loader, the spring forming fixture for the brake light switch was set improperly, resulting in some springs with undersized inner diameters. This causes excessive load …
In the driver assistance system of large tractors, the control program in the driver assistance control unit rewritten under improvement measure (Measure 564) is inappropriate. When a trailer without ABS is connected, …
The rear brake chamber of large trucks has insufficient structural strength. When driving at 80 km/h over lane markings (vibration lines) on expressways, the vibration frequency can cause cracks to develop in …
Some door speaker hole covers were not installed due to improper parts list during manufacturing. As a result, the airbag sensor inside the door may not function correctly during side-impact collisions, potentially …
The selector cable bushing for the automatic transmission is made of inappropriate material, resulting in insufficient strength in some units. The bushing may fracture, preventing proper shift position transmission to the transmission. …
In large trucks, the Driver Assistance Control Unit (DACU3) shutdown program is inappropriate, causing DACU3 to enter restart standby mode when an error is detected during system shutdown phase. As a result, …
In infant-dedicated vehicles, the positioning of the restraint pipe fastening bolt between the driver seat and rear seat is inappropriate. During sudden braking and similar events, infants may contact this bolt and …
The passenger-side airbag may develop unexpectedly high internal pressure during deployment in high-temperature conditions due to inadequate review of deployment characteristics. This may cause the bag to rupture or the bag-retaining bracket …
The inflator (inflation device) for the passenger-side airbag has inadequate moisture-prevention measures for the gas generant, which may degrade due to repeated temperature and humidity fluctuations. This may cause the inflator container …
The passenger seat airbag inflator lacks adequate moisture protection for its gas generant, which may degrade due to repeated temperature and humidity fluctuations. This creates a risk of inflator container rupture during …
The airbag control unit contains a power supply circuit capacitor with inadequate electrical conductivity, resulting in unstable voltage regulation. Consequently, the airbag warning light may illuminate and the airbag and seat belt …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.