Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 47 of 175
At the brake chamber piping connection, improper selection of the connecting fitting allows the brake piping to deflect significantly under driving vibration and similar conditions. The stress from this deflection can damage …
Improper routing of the battery harness allows interference between the transmission mount and the harness, causing insulation damage. This can result in harness short-circuiting, blown fuses, illumination of warning lights, and in …
On the braking device of the trailer's first axle, the clearance between the connecting fitting of the air hose connected to the brake chamber and the air tank is inadequate. When wheels …
The regenerative braking program in the powertrain control unit is inappropriate, which may cause an extended delay in transition to friction braking when regenerative braking fails. This may not meet the safety …
The roof bed mattress material selection is inadequate, causing the bed frame to corrode due to rust. This may result in bed frame damage and, in the worst case, the roof bed …
In the transmission control unit, due to an inappropriate control program, if the vehicle is manually shifted from an even gear to neutral while driving and brought to a stop in that …
On large trucks and buses equipped with air suspension, the spring securing the rear brake shoe is improperly set. Vibration during operation causes the shoe to vibrate and strike the clip (a …
Certain replacement inflator units for driver-side airbags have inadequate moisture-prevention measures for the gas generant. If such an inflator is installed during vehicle repair and used as-is, repeated large temperature fluctuations in …
In the steering system of large trucks, improper fit dimensions between the axle beam and kingpin can cause the kingpin retention force to decrease with repeated heavy use, potentially allowing the kingpin …
In some airbag control units, improper adhesion of the negative terminal in the capacitor causes unstable voltage. This may result in the airbag warning light illuminating and the airbag and seatbelt pretensioner …
In the brake booster pump of the electronically controlled hydraulic brake system, the injection mold for the plastic brush holder, which is a component of the pump motor, is improperly designed, resulting …
On the axles of crane carrier vehicles, improper design specifications result in insufficient knuckle thickness in some units. Continued long-term use may cause cracks to develop on the upper knuckle, potentially resulting …
In LPG-specification engine forklifts, the mounting bracket for the LPG vaporizer has insufficient strength. Repeated operations that apply hydraulic load during low idle, combined with engine vibration, can cause cracks to develop …
In the transmission control computer of vehicles equipped with an automatic transmission, the clutch control program is inappropriate. When range signal noise is detected during driving in D-range (including manual mode), unintended …
In the electric power steering system, insufficient maintenance of the connector processing equipment has resulted in improper insertion of circuit board terminals in some units. This may cause circuit disconnection due to …
The solder terminal connections in the fuel tank pump motor wiring may develop poor contact due to insufficient solder surface preparation, causing solder cracks and separation. This can lead to overheating and …
In small truck mixer-specification vehicles, the brake vacuum hose has an inappropriate shape, and due to wiring variations, the hose may be kinked during assembly. This delays negative pressure supply, causing the …
Some fuel hoses have insufficient elasticity due to inadequate molding control. These hoses may deform due to engine heat and vibration, contact the steering shaft, and in worst case, become damaged and …
Rear seat buckles and seat belts in all seating positions may have insufficient fastening torque due to improper tightening during assembly. Consequently, the nuts may loosen due to driving vibration and similar …
The mounting nut of the airbag control unit may have insufficient fastening torque due to improper tightening during assembly. Consequently, the nut may loosen due to driving vibrations and in the worst …
① The accelerator and brake support brackets may have insufficient fastening torque due to improper tightening procedure. Consequently, the nuts may loosen due to driving vibration, and in the worst case, the …
The wire harness of the electric power steering system may be pinched between the cross member and the underpanel due to improper underpanel mounting. This can damage the wire harness insulation, causing …
2. The air conditioning blower motor connector has an improper shape. When using a regulator not specified by the manufacturer, poor contact can occur between the regulator and wiring. This causes the …
1. The air conditioning blower motor housing has an inappropriate shape, allowing rainwater that enters the housing to accumulate. This causes corrosion of the blower motor shaft, increasing motor resistance and raising …
The gas generant in the passenger-side airbag inflator may degrade due to repeated cycles of environmental temperature and humidity changes. As a result, abnormally elevated pressure may occur within the inflator during …
In vehicles equipped with wheelchair boarding ramps, the rear wheel brake line routing design is inadequate, resulting in improper installation of the brake lines. Consequently, the vehicle stability control system may not …
The inflator (inflation device) of the driver-side SRS airbag replacement unit may experience degradation of the gas generant due to repeated environmental temperature and humidity fluctuations. Consequently, abnormal pressure rise may occur …
The gas generant in the passenger-side airbag inflator may degrade due to repeated cycles of environmental temperature and humidity changes. Consequently, the pressure inside the inflator may rise abnormally during airbag deployment, …
The gas generant in the passenger-side airbag inflator may degrade due to repeated environmental temperature and humidity fluctuations. As a result, abnormal pressure rise may occur inside the inflator during airbag deployment, …
The gas generator in the passenger-side airbag inflator may degrade due to repeated environmental temperature and humidity fluctuations. As a result, the internal pressure in the inflator may rise abnormally during airbag …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.