Before you buy, check it isn't under a dangerous recall.

Fuel tank caps may be equipped with rubber seals of low gasoline resistance due to improper manufacturing processes. Continued use can cause cracks in the seal, leading to fuel leakage and potential …

Rear outer door handles may have insufficient sealant application on the switch due to improper manufacturing process. Water intrusion from rain and other sources can degrade the switch circuit, potentially preventing the …

Takata airbag inflator may rupture, ejecting metal fragments

The starter lacks sufficient waterproofing. When driving through standing water or puddles at speed, water may enter the relay inside the starter. Continued operation can cause contact points to short circuit, resulting …

Front wheel brake hose routing design is insufficient. During steering, the hose may contact the vehicle body. Continued use risks hose damage and potential perforation, resulting in reduced braking force.

High-voltage battery modules may develop deviations in critical technical parameters during use due to improper manufacturing processes. During high-voltage battery charging, the affected module may overheat, potentially resulting in fire in severe …

In the steering valve that controls rotation of the shovel loader, improper manufacturing processes have resulted in some units where the spring inside the shock valve pressure adjustment screw is not assembled …

The upper circlips on the left and right front air springs may not be properly assembled due to inadequate manufacturing process. Vibration during operation may cause the circlips to loosen, leading to …

At the fuel tank filler opening, when gasoline overflows during refueling, vaporized gasoline may be drawn into the radiator by the engine cooling fan. If the radiator is at high temperature, vaporized …

The parking brake release tool is not equipped due to inappropriate installation instructions. As a result, if the parking brake becomes stuck due to malfunction or other reasons, it cannot be released, …

The rear shock adjuster mounting bracket has insufficient structural design. Vehicle vibration at high engine RPM causes the bracket to resonate and develop cracks. As cracks propagate and fracture, the rear shock …

Takata airbag inflator may rupture, ejecting metal fragments

In the electronic air dryer, when replacing the legacy Central Chassis Input/Output Module with the current model during repair, improper firmware programming instructions result in the air dryer regeneration software not being …

In the electronic air dryer, when replacing an older Central Chassis Input/Output Module with the current model during repair, improper programming instructions result in the air dryer regeneration software not being updated …

In high-pressure fuel pumps, improper manufacturing processes have resulted in some units where the fixing bolts are not tightened to the correct torque. Consequently, during use, the pump fixing may loosen, causing …

Certain supply pumps in replacement repair parts have insufficient component strength due to inadequate surface treatment in the manufacturing process. Repeated high-load operation may cause cracks to develop, potentially resulting in fuel …

The starter's waterproofing design is inadequate. Water can penetrate inside the starter relay when driving through puddles at high speed. Continued use may cause contact point short-circuiting, resulting in engine failure to …

The starter has insufficient water-resistant design. When driving through puddles or standing water at speed, water may enter inside the starter relay. Continued operation could cause contact points to short circuit, resulting …

The power cable of the fuse box has improper manufacturing instructions, resulting in insufficient clearance between the cable and the passenger-side footrest panel in some vehicles. During use, the power cable may …

In the steering valve of the shovel loader, due to improper manufacturing process, the spool bore that distributes hydraulic flow is distorted in some units. As a result, when steering operation is …

The brake system backplate has insufficient design review, and in some cases interferes with the load-handling device lift cylinder. This interference causes friction and wear between the backplate and lift cylinder during …

The internal circuit board of the LED approach lamp in the left side mirror has insufficient design considerations. During use, gaps and cracks develop in the potting material (insulation), allowing water and …

The steering controller holder supplied with agricultural tractor steering controllers has insufficient design against water ingress, allowing water to enter the holder interior and causing rust on the spline connecting the internal …

In right-hand drive specification vehicles, the airbag control unit software contains an improperly configured door pressure sensor identification program intended for left-hand drive specification due to inadequate manufacturing processes. Consequently, side airbag …

The control unit of the electric brake booster has insufficient control program review. When Travel Assist is active and the steering wheel is released for a certain period, the system may misidentify …

In the high-voltage battery cell module, improper manufacturing may cause misalignment of the positive electrode sheet end, resulting in separator damage. This can lead to internal short circuits within the cell module, …

Certain high-voltage battery cell modules have been manufactured improperly, with excessive pressure applied to cells during compression by pressure plates, resulting in excessive residual stress beyond acceptable limits. Over time, stress-induced damage …

Takata airbag inflator may rupture, ejecting metal fragments

In high-pressure fuel pumps, improper manufacturing processes have resulted in some units where the mounting bolts are not tightened to the correct torque specification. Consequently, the pump mounting may loosen during use, …

Certain high-voltage batteries have inadequate waterproofing at openings due to improper manufacturing processes. Prolonged use causes loss of seal integrity, allowing moisture ingress into the battery and resulting in insulation failure and …