Before you buy, check it isn't under a dangerous recall.

In the power transmission system of an agricultural tractor, due to insufficient review of the control software, when the brake is applied after the system has automatically switched from four-wheel drive to …

On the monitor panel, which serves as the tire roller's instrument panel, the waterproof packing may be improperly installed during manufacture. This can allow water to enter the panel, impair the LCD …

In the electronically controlled brake system computer, inappropriate control program settings may cause the vehicle weight to be incorrectly learned as lighter than actual during use. If the discrepancy between the actual …

Some brake hose heat shields have not received anti-corrosion treatment due to improper parts management. As a result, the heat shield may corrode during use; in the worst case, if it detaches, …

In the sunroof side moldings, some have insufficient adhesion due to an improper bonding process. If use continues, the side molding may detach and produce abnormal noise, and in the worst case, …

On van-type trucks, improper installation instructions for the rear combination lamp cause the tail lamp or rear reflector mounting position to not comply with safety standards.

On swap body container carriers, the rear underrun protection device is not mounted close to the rear end of the vehicle, as it should be attachable from the rear, due to improper …

Due to improper design instructions, the driving headlamp on electric forklifts cannot be manually turned off immediately, which violates the technical standards for lighting devices and renders it non-compliant with safety standards.

Insufficient design verification of the LPG pressure gauge setting on engine-powered forklifts may cause pointer drift when pressure repeatedly exceeds specification, resulting in the gauge indicating more fuel than actual. Continued operation …

Due to inadequate work instructions, the seal ring at the fuel pump mounting section may not be correctly installed, impairing the seal. Continued use can lead to fuel leakage.

An improper control program in the lithium-ion battery controller can cause unnecessary fault detections. This results in an EV system warning message on the instrument cluster and limits drive motor output. In …

Due to an insufficient pulley design review in the engine water pump, some pulleys have inadequate engagement with the shaft. Continued use may cause the pulley to detach, loosen the timing belt, …

In vehicles equipped with an auxiliary seat, the side sliding window stopper on the rail may not be positioned as designed due to an improper manufacturing process. This can reduce the effective …

Due to insufficient verification during production, the noise label shows an incorrect average vehicle speed at the onset of wide-open throttle acceleration, causing non-compliance with the technical requirements of UN Regulation No. …

In the braking system, the design review of the pivot pin connecting the rear brake pedal and push rod was insufficient, which may cause the pin to rust. Consequently, if use continues, …

The rear brake hose retainer and heat shield tube were inadequately designed, resulting in insufficient heat shielding. During operation, radiant heat from the nearby exhaust pipe can damage the brake hose outer …

In the digital instrument cluster control unit, insufficient design review of the control program may prevent the cluster from starting correctly at vehicle startup, resulting in a blank screen. This could make …

In the front brake, due to inadequate parts control during manufacturing and improper in-plant repair work, some vehicles had the front brake cable excessively adjusted while air was trapped in the master …

In the second-row seat belt reminder system, insufficient consideration of the buckle wiring routing may subject the wiring to repeated stress during belt attachment and detachment, potentially causing a wire break. This …

Due to inadequate routing of the second-row seat belt buckle wiring, repeated stress during fastening/unfastening may cause the wiring to break, potentially resulting in incorrect alerts of the seat belt fastened status.

The impeller (resin vane) in the low-pressure fuel pump may have low resin density due to improper molding conditions, causing it to swell and deform from fuel. This can lead to impeller …

The second-row seat belt warning system has insufficient routing consideration for the buckle electrical wiring. Repeated stress is applied to the wiring during seat belt fastening and unfastening, which may cause the …

In the battery EV system, insufficient validation of the drive battery computer control program may cause incorrect recognition of the battery control state under specific conditions, leading to a false fault detection. …

On certain forklifts, the exhaust front tube has insufficient strength due to inadequate design review, resulting in low material strength and machining precision. Continued use may cause the front tube to fracture …

Wheel bolt may loosen under sustained high load due to insufficient design verification, possibly leading to bolt detachment and wheel loss.

Due to improper management of the machine that processes the fuel pipe connection on the engine common rail, some connections have insufficient sealing. Continued use may cause fuel to leak from this …

Due to inadequate process control during bulb manufacturing, some turn signal bulbs contain foreign matter or have cracks, which can cause premature filament damage and possible failure of the turn signal to …

In the engine, due to an improper position of the blow-by gas outlet in the head cover, excessive oil may accumulate in the head cover during continuous driving on slopes. This oil …