Before you buy, check it isn't under a dangerous recall.

The auto-tensioner spring that maintains constant accessory belt tension has inadequate durability. With aging, tension decreases, causing belt deflection and load concentration, which may result in belt fracture. Continued use could lead …

Due to a design defect in the audio/air conditioning control unit, when the hazard flasher switch is operated to turn on the hazard flasher, there is a possibility that the hazard flasher …

Stainless steel hinges installed on the upper rear posts of large dump trucks have inadequate welding range in the hinge components, resulting in insufficient strength of the attachment. Continued use may cause …

Insufficient heat treatment occurred during manufacturing of outboard joint balls, a component of the rear wheel driveshaft assembly at the supplier. Consequently, balls with inadequate hardness were used, which may experience wear …

In the PDA (Proactive Driving Assist) of the driving support system, due to an inappropriate control program, if the brake pedal is operated during deceleration control by the PDA, the brakes may …

In the front-wheel braking system, insufficient component management during assembly may result in brake discs of incorrect dimensions being installed. In such cases, the system may not comply with the technical requirements …

Due to improper fuel tank manufacturing, the fuel pipe connector mounted on the tank top may not be correctly seated. Consequently, the connector may detach due to driving vibrations or other factors, …

The impeller (resin-molded rotor) of the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in reduced resin density, causing swelling when exposed to fuel. This can cause …

The bracket securing the manual transmission select cable has an inappropriate shape, causing the select cable and fuel hose to contact in some vehicles. Continued use may result in the fuel hose …

In bus battery cables, improper terminal crimping during manufacturing has caused damage to some cables. Continued use may result in cable breakage and inability to restart the engine.

Battery cables on buses may be damaged due to improper terminal crimping during manufacturing. Continued use could result in cable breakage and engine restart failure.

During fast charging or in preparation for fast charging, the cooling program for the touchscreen's processor may be insufficient, resulting in inadequate cooling. This can cause processor performance degradation or restart, resulting …

In the braking system of electric forklifts, due to inappropriate programming of the control controller, the backup braking function may fail to operate during low battery voltage error conditions, potentially preventing safe …

In the outrigger apparatus of aerial work platforms, improper routing structure may cause wiring and hydraulic hose covers to snag on internal components. This can result in bending and damage to the …

In the powertrain, some gearboxes have insufficient oil fill due to equipment failure during manufacturing. This may cause clutch slippage and, in worst cases, display a warning message and interrupt power transmission. …

In the power transmission system, some gearboxes have insufficient oil fill due to equipment failure at the production facility. This can cause clutch slippage and, in worst case, display warning messages and …

In large trucks, the Key ON relay and ECM relay have insufficient durability. The resin bobbin inside the relay shrinks due to heat, creating gaps between the bobbin and the coil. If …

The EGR pressure sensor integrated in the exhaust gas recirculation (EGR) device has insufficient corrosion resistance to exhaust gas. Corrosion of the sensor can cause abnormal sensor output, resulting in warning light …

The coolant pump installed in diesel engines has improper bearing seal design, allowing coolant to infiltrate the vacuum circuit under controlled operation. This causes malfunction of vacuum circuit components, resulting in illumination …

The rubber sleeve installed on the brake booster has an inadequate design, allowing moisture that enters the gap between the booster housing and sleeve to remain trapped for extended periods without draining. …

In the headlight control units that regulate adaptive headlights, inadequate manufacturing control has resulted in improper calibration of headlight sensors in some vehicles. Consequently, depending on vehicle load conditions, the light axis …

In the engine's high-pressure fuel piping, inadequate process control during assembly has resulted in fine particles being trapped in the seal between the fuel rail and injector. During use, this seal can …

Some units may be susceptible to accelerated corrosion and fatigue of the steering shaft. Continued use in this condition may result in steering shaft fracture, loss of driving stability, and potential inability …

In the standing assist function, even after implementing measures under improvement countermeasure notification number 640, the caliper pad may not separate from the disc when the standing assist is disengaged, similar to …

In the electrical system of rotary snow removal vehicles, improper wiring fastening causes alternator and ground wiring to chafe against wiring clamps during driving vibration, resulting in insulation damage. Continued use may …

In the rotary snow removal vehicle's control system, the forward/reverse shift lever has inadequate strength. Continued use may cause wear at contact points, and in the worst case, the forward/reverse shift lever …

In the braking system of a rotary snow removal vehicle, the mounting section shape of the air compressor pulley is inappropriate. Due to vibration during operation, the pulley fixing nut may loosen …

In the running gear of rotary snow removal vehicles, the hub bolts for wheel attachment have inadequate strength and may fracture. Hub bolts and hub nuts can then fall into the brake …

Insufficient layout validation during design may allow a portion of the rear wheel arch liner (wheel house cover) to contact the rear brake pad position sensor cable through vibration, potentially damaging the …

Rear sliding seat rails are installed with misaligned rail geometry, causing the seat locking slot position to be slightly offset. As a result, some seats are not securely fixed. In the event …