Before you buy, check it isn't under a dangerous recall.

The holder supplied with the steering controller of agricultural tractors has insufficient design against water ingress and vibration. With extended use, rust develops and wear occurs on the spline connected to the …

The vacuum pump that supplies negative pressure to the brake booster has an internal check valve made of inappropriate material. In extremely cold conditions well below freezing, moisture adhering to the check …

In the engine, improper manufacturing process control of the crankcase and transmission case results in insufficient sealing at the mating surfaces, which may cause transmission oil leakage. This can lead to inadequate …

In the fuel tank, inadequate maintenance of manufacturing equipment has resulted in insufficient welding between the fuel tank body and filler pipe. Vibration and other forces applied to the vehicle body may …

The bolts securing the drive gear to the crankshaft on the engine have insufficient durability. During hard acceleration, excessive stress concentrates on the bolt threads, causing cracks to form. Continued use may …

In the engine, inadequate control during manufacturing of the crankcase and transmission case results in insufficient sealing at the mating surfaces, potentially causing transmission oil leakage. This can lead to poor lubrication, …

The stop switch contact lubricating grease material and improper assembly of the switch to the brake lever bracket can cause the grease to carbonize due to arc discharge between switch contacts. Continued …

In the combination meter, improper condition settings when distributing control programs for field service resulted in incorrect control programs being written to some units. Consequently, the combination meter may fail to display …

In mild hybrid vehicles, improper battery control in the engine control computer and mild hybrid battery can cause voltage differences between cells within the battery. Continued use may increase this voltage differential, …

①In mild hybrid vehicles, the transmission control computer has inadequate clutch control. When restarting the stopped engine during motor-driven EV operation, the clutch engagement timing connecting the motor and engine may shift. …

The exhaust gas recirculation (EGR) module in diesel engines has insufficient durability consideration, causing coolant leakage over time. In such cases, soot contained in exhaust gas mixes with coolant and deposits inside …

Due to improper manufacturing instructions for the semi-trailer brake system, incorrect brake chambers and spring brake chambers have been installed. In the worst case, this may result in extended braking distances.

In light-duty trucks, the electric parking brake system control program is improper, which may prevent correct recognition of the parking brake cable stroke during electric parking brake operation. Repeated actuation of the …

In light-duty trucks, due to inappropriate control programming in the electric parking brake system, the system may falsely detect normal parking brake cable stroke as abnormal during electric parking brake operation, potentially …

In light-duty trucks, due to an inappropriate control program in the electric parking brake system, activating the electric parking brake immediately before stopping may cause the system to falsely detect parking brake …

The PTC heater, which supplements cabin heating, has improper control, causing it to operate at maximum output. When used repeatedly in this condition, heat generated by the PTC heater can deform the …

In the driving support system of large trucks, due to improper programming of the vehicle control ECU, when the Driver Abnormality Response System (EDSS) activates and brings the vehicle to a stop, …

The reverse control unit has insufficient manufacturing instructions, resulting in sealing defects during assembly. Moisture can enter the unit, causing corrosion of internal electrical contacts. Continued use may lead to overheating within …

In the front brake master cylinder, additives contained in the diaphragm material are improper. When these additives leach into the brake fluid, they cause the seal to swell, potentially blocking the oil …

On truck flat beds, floor hooks mounted on the bed surface may detach when cargo is secured with lashing equipment due to insufficient design review of the hooks. In the worst case, …

The hood latch and wire design is inadequate, causing tension on the wire due to vibration during driving. This may cause the latch to actuate, and in the worst case, the hood …

The combination meter warning display program is inappropriate, so the brake system warning light in the combination meter does not illuminate when any function of the collision mitigation system (short-range collision mitigation …

In hybrid vehicles, improper machining of high-pressure fuel pump components can allow metal particles to become trapped between pump components and machining fixtures during processing. This can cause cracks to develop at …

In hybrid vehicles, improper machining processes for high-pressure fuel pump components can cause metal particles to become lodged between pump components and machining fixtures. This can result in cracks forming at the …

In the braking system of combine harvesters, due to improper manufacturing processes, the spring pin connecting the parking brake pedal and brake arm may disengage. If operation continues in this condition, the …

Front and rear window glass may have insufficient adhesion due to inadequate cleaning during the glass manufacturing process. This can result in water ingress from the glass bonding surface and wind noise …

In the electric power steering gearbox, improper mesh load settings between gears cause grease applied to the meshing surfaces to be expelled, resulting in increased sliding resistance. This may increase steering effort …

Some roof trim panels exceed specification thickness due to improper molding equipment settings. This may prevent the curtain airbag mounted on the back of the roof trim from deploying properly.

The fuel pump has an inadequate connection structure with the fuel hose. When used in salt-laden environments, cracks may develop on the resin discharge port surface. Continued long-term use can cause cracks …

The tie rod connecting the steering shaft to the tire has insufficient design consideration, resulting in improper mounting angle. During steering operation, excessive load is applied to the tie rod. Continued use …