Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 24 of 175
In the camshaft chain tensioner that adjusts camshaft chain tension, internal components deteriorate through use, causing the plunger to be pushed back and potentially lock. If operation continues with the plunger locked, …
The speedometer (meter unit) may restart while driving due to improper control programming. During restart, the operator will be unable to confirm speed and other information necessary for operation.
The seat strap (rear seat grab handle) attached to the driver's seat of the seating equipment may have insufficient strength due to improper processing conditions during manufacturing. Continued use in this condition …
In the steering column switch, due to improper control unit programming, when system voltage drops below 6V during low battery charge conditions such as cold engine starting, an electrical fault may be …
In the in-tank unit of the fuel pump, the clearance design between the resin impeller and cover is inadequate. As a result, the resin impeller may deform due to elevated fuel temperature, …
In shovels and loaders, improper assembly of the heating element in heated fuel filters can cause the heating element to tilt and contact the sight glass. Continued operation may result in the …
In the generator, the rib height in the left crankcase cover interior where the stator coil is assembled is set improperly, causing the coil wire to contact and damage the rib, resulting …
In the driver seat seatbelt, steering column, and driver seat airbag, improper part number specifications in the replacement/repair parts catalog resulted in some vehicles being equipped with non-specification parts. Consequently, under certain …
Replacement service parts catalogs contain incorrect part number specifications for (1) driver-side seat belt or steering column, and (2)(3) driver-side airbag. Consequently, non-specification parts have been installed on some vehicles. In the …
(1) Driver seat belt or steering column (2)(3) Driver seat airbag: Improper part number instructions in the replacement/repair parts catalog have resulted in some vehicles being fitted with parts that do not …
Manufacturing defects in high-voltage battery cell modules may cause malfunction of the high-voltage battery. In rare cases, this can result in battery discharge, which in the worst case may lead to fire.
The inflator (inflation device) of the driver-side two-stage deployment control airbag has inadequate moisture-prevention measures for the gas generant, which may degrade the gas generant through repeated absorption and desorption cycles caused …
The bolt length selected for fastening the handlebar stem is inappropriate, causing bolt damage during the tightening process. This can result in bolt fracture due to vibration during use, leading to loss …
Takata airbag inflator may rupture, ejecting metal fragments
In welfare vehicles (equipped with manual driving controls), the nut that fixes the lock mechanism for holding the brake on the lever brake may loosen due to improper tightening. If use continues …
The main wire harness routing is improper, and vibration during operation may cause contact with vehicle structural components such as the frame. This can damage the harness insulation, causing internal wire short …
The brake pedal rubber bumper uses inappropriate material with insufficient durability. Degradation during use can cause the bumper to crack and detach. This may result in intermittent brake light illumination. Additionally, the …
During type-designated small truck final inspections, the measurement accuracy of the brake testing equipment was inadequate, which may have resulted in failure to properly verify brake compliance with Road Transport Vehicle Safety …
Due to improper programming of the steering wheel electronics, the Steering & Lane Control Assist (LSA) and Lane Change Assist (SWA) may not correctly acquire signals related to Hands Off Detection (HOD). …
The driver's seat airbag inflator may accumulate moisture when exposed to high-temperature, high-humidity environments over extended periods. During airbag deployment, abnormal pressure rise in the inflator can cause the inflator vessel to …
Front seat belt tensioners with force limiters may have insufficient component assembly force due to inadequate manufacturing controls. In the event of frontal airbag deployment during a collision, seat belt restraint force …
In transmission electrical wiring, improper routing design causes excessive force on connector sealing sections, deforming them. This compromises seal performance, allowing rainwater ingress into connectors and causing short circuits. Battery drain can …
The auxiliary battery located beneath the front passenger seat has improper routing of the positive power wiring, which in some vehicles interferes with the seat frame. This causes the insulation to wear …
The rear SAM (signal detection control module) control unit located in the trunk has improper installation positioning. During rainy conditions when the trunk is in use, rainwater from the trunk lid may …
Certain shovel loaders are equipped with axles manufactured based on incorrect heat treatment instructions. Continued use of these units may result in loosening of bolts securing the axle shaft, hydraulic fluid leakage, …
In the variable valve timing unit, improper machining of the sprocket surface on a constituent component may cause the mounting bolts to loosen. This prevents the unit from operating properly, resulting in …
In the fuel pump in-tank unit, the clearance design between the resin impeller and cover is inadequate. When the resin impeller deforms due to fuel temperature rise or other factors, it may …
The instrument cluster program in the brake booster warning system is defective. When the brake booster fails, the warning light does not illuminate. After confirming the warning message, an incorrect warning light …
Manufacturing defects in high-voltage battery cell modules may cause high-voltage battery malfunction. In rare cases, the high-voltage battery may discharge, potentially leading to fire in the worst scenario.
Due to a manufacturing defect, the pressure spring required for the power-folding function of the third-row seat may not be correctly installed or may be completely missing. Consequently, the seat backrest may …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.