Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 76 of 173
In braking systems equipped with a dual combined brake system that operates front and rear wheel brakes in coordination, the structure of the secondary master cylinder that transmits braking force from the …
Certain airbag control units have insufficient electrical noise immunity. Noise generated from vehicle electrical components may damage the IC chip within the unit during use, and in the worst case, could cause …
The control module circuit board that regulates the fuel pump may have foreign material adhered to it due to improper manufacturing. This can cause circuit short circuits, illuminating warning lights, and in …
The control program for the rear window defog device is inappropriate, causing continuous power supply in auto mode. This can cause the device to overheat, potentially resulting in fire.
In braking systems equipped with a dual combined brake system that synchronously operates front and rear wheel brakes, the secondary master cylinder structure that transmits braking force from front to rear wheels …
The fuel pump intake in the fuel tank has inadequate air-tightness in some units. This causes unstable fuel supply from the pump to the engine, resulting in rough engine acceleration and, in …
During correction work for handlebar peripheral component appearance defects, improper reinstallation of the handlebar holder has resulted in insufficient bolt torque on some units. Continued use in this condition may cause the …
In the system that alerts following vehicles via emergency flash lights and hazard warning lights during emergency braking or accidents, the control program is inappropriate, causing the hazard warning light flash frequency …
In fire truck (ladder truck) damping systems, improper welding between the rear-axle torque rod mounting bracket and frame undersurface can develop cracks at the weld due to repeated braking input. If use …
Variation in gas generator density was confirmed in certain driver-side SRS airbag inflators from recalled units. While the root cause remains undetermined, there is a potential risk that the airbag may not …
The driver-side SRS airbag inflator has inadequate moisture control after gas generant filling during manufacturing. This causes the gas generant to expand due to external temperature fluctuations during use, resulting in reduced …
The passenger-side airbag inflator may contain gas-generating material with insufficient density due to improper molding of the propellant or inadequate moisture prevention measures after molding. During airbag deployment, internal pressure in the …
In certain driver-side SRS airbag inflators, the container may rupture under internal pressure during airbag deployment, causing component fragments to scatter and potentially injuring occupants.
In the brake booster, the hose connection on the cabin side is positioned improperly, risking contact with the driver's foot. If this hose connection is pressed down forcefully, it may disconnect, causing …
The airbag control module contains an improperly coated circuit board. In high-humidity environments, the electrical circuit may corrode. Continued use risks circuit short circuits, illumination of the airbag warning lamp, and in …
Some alternators with insufficient generating capacity were installed during manufacturing. When high electrical loads are applied, such as during electric hydraulic power steering operation, the electrical load on the alternator causes internal …
Due to improper programming of the airbag control module, side curtain airbags and side airbags may inadvertently deploy when the vehicle tilts sharply left or right during driving.
The electric power steering control program is inappropriate. In cold conditions, the program may incorrectly determine a malfunction even when the electric power steering is operating normally. As a result, a warning …
On tank semi-trailers, improper process control of the welding between the suspension bracket cover plate and its reinforcing material results in insufficient metal penetration in some units. Consequently, running vibration and similar …
In tank semi-trailers, inadequate strength analysis of the frame (cross member) may result in cracking when excessive loads exceeding design values are applied during sharp turns. Continued use in this condition may …
In tank semi-trailers, insufficient weld strength in the reinforcement rib at the suspension bracket attachment point may cause cracks in the weld due to stress generated during braking. If use continues in …
The inflator (inflation device) for the front passenger airbag may suffer container rupture during deployment. Although the cause has not been determined, all vehicles will undergo preventive replacement of the inflator as …
The electronic stability control (ESC) system controller has an inadequate control program. During ESC operation, electromagnetic interference from the brake control drive motor may cause the yaw rate sensor signal built into …
The hydraulic clutch master cylinder has inadequate internal cleaning during machining, leaving manufacturing chemicals not fully removed. These chemicals react with brake fluid inside the master cylinder, causing gas bubbles to form …
In rotary snow removal vehicles, the fuel filter mounting bracket design is inadequate, resulting in insufficient vibration isolation against engine vibration. Engine vibration may cause cracks in the fuel filter, leading to …
The engine ECU control program has an improperly set learning limit value for idle air volume correction. When carbon accumulates on the throttle valve, idle air volume may become insufficient, potentially causing …
The fuel pressure sensor attached to the fuel line may have insufficient tightening due to improper manufacturing. This may cause fuel leakage from the fuel pressure sensor mounting point.
Improper assembly of inner arch liners installed within the front wheel fenders on the left and right sides; in some cases, the inner arch liner contacts the brake hose. Continued use in …
On trailers subject to mid-stage brake regulations with single-axle or lift-axle configurations, related components such as air control valves may be used beyond their service life limits, causing air leakage and reduced …
In the parking brake of wheel loaders, improper manufacturing instructions have resulted in incorrect positioning of the washer at the coupling between the parking brake actuation lever and push rod. Consequently, vibration …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.