Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 81 of 173
Improper process control during front brake caliper assembly has resulted in insufficient tightening of caliper mounting bolts. Continued use in this condition may cause the bolts to loosen, resulting in abnormal noise …
In the engine control unit power supply circuit, an incorrect wiring terminal fixing bolt was used on the power fuse. As a result, the fixing bolt interferes with the fuse holder partition …
Continued use with a damaged rear trailing arm resulting from impact in accidents or similar events may cause the rear trailing arm to fracture during operation, potentially affecting steering control.
In the variable valve timing unit, the sprocket surface of a constituent component has been machined improperly, which may cause the mounting bolts to loosen. As a result, the unit may not …
Due to manufacturing tolerances in the fuel system, the fuel pipe and injector component may not be installed properly. This can result in gaps at the attachment point during use, causing fuel …
In the fuel system, manufacturing tolerances between the fuel pipe and injector components may prevent proper installation of the fuel pipe and injector. This can cause gaps at the attachment point during …
Due to manufacturing tolerances between fuel pipes and injector components in the fuel system, some vehicles may not have proper installation of fuel pipes and injectors. This can result in gaps at …
The side stand auto-up reminder device has improperly routed and sized electrical wiring that can interfere with the rear wheel drive chain. Continued operation may cause the wiring to wear due to …
The fuel tray shape in the fuel tank is inadequate, allowing rainwater and other debris entering from the floor to accumulate in the fuel tray and potentially enter the fuel tank when …
The fuel tank drain tube is mounted in an improper position. During rain, water can enter the fuel tank through the drain tube outlet. If the fuel pump draws in water, engine …
Push-button type parking brake switches and emergency stop switches have improper manufacturing controls, resulting in some units having insufficient internal sliding clearances. In low ambient temperatures, thermal contraction of the switch body …
Improper manufacturing of the drive shaft has resulted in insufficient strength in the outer race section. As a result, the drive shaft may fracture during operation, rendering the vehicle inoperable.
When a key ring or similar accessory is attached to the ignition key, driving vibrations may cause the ignition key to move from the RUN position. This cuts power to the vehicle, …
In the engine compartment, improper installation of the rubber seal to the bulkhead causes the seal to adhere to the inner surface of the hood when opened and separate from the bulkhead. …
An incorrect ground wire is installed in the air conditioning blower motor. When the air conditioning is used, this ground wire may overheat and burn. This can cause the electric power steering …
When key holders or similar items are attached to the ignition key, vibrations during driving may cause the ignition key to move to a position other than RUN. This cuts power to …
The union nut at the brake pipe joint may loosen during use due to improper initial tightening. This can cause brake fluid leakage, resulting in warning light illumination, reduced braking force, and …
Front wheel rims have improper finishing from manufacturing, resulting in poor tire contact. Air leaks between the rim and tire bead. Continued use causes tire pressure loss, heavy steering, and reduced handling …
On the front lower arm, anti-corrosion coating application on the ball joint bolt portion is inadequate, causing the bolt to corrode during use in some cases. This reduces bolt strength and can …
In the front brake master cylinder, some units have foreign matter adhered to the reservoir tank due to inadequate cleaning after thread machining. Continued use in this condition may result in corrosion …
The fuel control module, which regulates fuel flow, has defects in the connector pins and electronic circuit board manufacturing, resulting in foreign material adhesion on some units. This foreign material can cause …
Some fuel pumps have excessive crimping of wiring and terminals due to improper crimping work. This causes increased electrical resistance, leading to overheating of the affected area, melting of surrounding components, and …
In the fuel pump, the crimping of wiring and terminals is improper, resulting in some units being over-crimped. This causes increased electrical resistance, leading to overheating of the affected area and melting …
Due to improper clearance design between the plastic impeller and fuel pump cover, the plastic impeller and fuel pump cover may interfere with each other as fuel temperature rises during operation. As …
On vehicles equipped with ABS, the mounting structure of the rear-wheel ABS sensor is inadequate, resulting in poor sealing at the mounting surface in some cases. Consequently, mud and water infiltrating through …
In direct-injection turbodiesel engines, the fuel injection pump seal may develop cracks due to improper manufacturing and design. If operation continues in this condition, cracks may propagate and eventually penetrate completely, potentially …
The vehicle-side connector of the side and curtain airbag control module has some units with incorrectly arranged terminals. As a result, in the event of a collision, the seat belt pretensioner on …
Some large and medium-duty trucks have insufficient grease fill in the inner hub bearings. Continued operation in this condition may result in poor lubrication of the hub bearings, potentially leading to loss …
In the steering system, the intermediate shaft connecting the steering wheel and gearbox may have welding defects at the joint due to improper positioning of the welding equipment setup. Continued use in …
In auxiliary brake lights, improper electrical circuit board design within LED elements may cause circuit board corrosion and loss of conductivity. Continued use may result in failure of the auxiliary brake light …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.