Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10558 recalls on record · page 26 of 352
The power liftgate control module on the back door has inadequate waterproof design. Rainwater and other moisture can travel through the rear gate opening and intrude into the connection terminal section of …
High-voltage batteries may contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in battery thermal anomalies and fire.
High-voltage batteries may contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in thermal battery anomalies and fire.
Some propeller shafts have insufficient interference fit depth of the universal joint pipe, resulting in inadequate strength. During use, cracks may develop at this location, and in the worst case, propeller shaft …
In the Collision Mitigation Braking System (FCM), the front radar ECU control program is inappropriate. When the front camera temperature rises due to parking in direct sunlight, if the FCM temporarily stops, …
In vehicles approved under Regulation No. 16 (Large Vehicle Seat Belt Non-Fastening Warning Device), due to an inappropriate control program, when the seat belt is fastened or unfastened under specific conditions at …
Front and rear glass bonding may be insufficient due to inadequate process control during the adhesive application process. Continued use in this condition risks the adhesive failing due to vehicle vibration and …
In the panoramic view or back guide monitor, insufficient management of the welding equipment fails to ensure waterproofing at the camera case joint surface, allowing rainwater and similar moisture to infiltrate. This …
Front and rear window glass may have insufficient adhesion due to inadequate cleaning during manufacturing. This can result in water infiltration at glass bonding surfaces and wind noise during driving. In the …
Certain front output shafts have been pressed onto their bearings with excessive force due to improper manufacturing, resulting in fitting force exceeding specification after assembly. This causes bearing deformation, spline loosening, and …
In the panoramic monitor control module, when the software was updated, the software version information was not updated accordingly. This does not comply with the software update management requirements specified in UN …
In the brake operating simulator of the electric servo brake system used as a replacement part, improper manufacturing processes may allow assembly oil used during production to infiltrate the pressure sensor. Consequently, …
On large refrigerated trucks, the work instruction for the left front U-bolt securing the chassis frame to the subframe was inappropriate, resulting in some vehicles having insufficient clearance between the vehicle-side wiring …
In cargo boxes of large refrigerated trucks and similar vehicles, the caulking application at the rivet cover joint on the corner rail section is excessive, resulting in insufficient bonding in some cases. …
The caps attached to both ends of the anti-intrusion device have inadequate manufacturing instructions and control, resulting in some cap portions having a radius of curvature less than 2.5 mm. Consequently, these …
Due to inappropriate programming in the gateway module, when the position lamps are switched on and the ambient light sensor detects a certain brightness level, the position lamps, tail lamps, and license …
The gateway module that detects brake pad wear has improper programming, which may prevent detection of brake pad wear condition and fail to notify the driver of the wear status.
In the charging connector of plug-in hybrid vehicles, improper work instructions have resulted in incorrect routing of the temperature sensor wiring within the connector. Consequently, the temperature sensor cannot detect temperature, causing …
The noise label and frame number label contain insufficient verification of recorded content, resulting in incorrect exhaust noise values and measurement engine speeds. This fails to comply with UN Regulation No. 41. …
Agricultural tractor front suspension ball joints may be improperly assembled and not correctly attached to the knuckle housing. Continued operation in this condition can result in premature ball joint wear or knuckle …
The side airbags installed on the left and right front seats may inadvertently deploy in frontal collisions and similar impacts where such airbags are not required, due to improper programming of the …
The air deflector installed on the underbody in front of the rear wheels does not comply with exterior technical standards (UN Regulation No. 26) due to insufficient shape verification during development.
In the fuel evaporative emission control device (canister), some units have insufficient activated carbon filling due to improper canister case shape. Additionally, some canister cases may deform during use, creating gaps inside …
Forklift steering axles may have non-standard dimensions due to improper machining during manufacturing. When the steering wheel is turned to maximum lock in the left direction, the left rear wheel may interfere …
In rotary snow removal vehicles, due to oversight during factory inspection, the pressure switch for the charge pressure low warning lamp may have been shipped in an unset state. In the worst …
Driver and front passenger seat frame to backrest attachment bolts were not torqued to specification due to inadequate manufacturing control. During collision, excessive force applied to the backrest may cause bolt failure, …
The drive motor bearing assembly fixture was improper, causing damage to the oil seal O-ring during assembly in some units. Consequently, cooling oil leaks from the drive motor during use, resulting in …
The control program in the CAN gateway, which is the communication control device between in-vehicle control units, is inappropriate, which may result in communication malfunction among in-vehicle control units. As a result, …
The navigation control unit has an improper control program, which may cause the navigation system to malfunction. As a result, camera video for direct front and left confirmation may not be displayed. …
Some aluminum wheels have improper machining at the wheel mounting surface, resulting in insufficient clamping face dimensions. This causes hub nuts to bottom out with insufficient clamping force. Continued operation in this …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.