Before you buy, check it isn't under a dangerous recall.

In the high-voltage battery management system, due to improper control programming, concentrated data requests from other control units can cause memory overload, triggering a reset that may inadvertently open the battery contactor. …

The engine control unit contains incorrect control software due to improper production specifications. Consequently, redundancy for catalyst degradation over time is insufficient, and exhaust gas values may fail to meet regulatory limits.

Transmission electrical wiring has inadequate cable routing design, causing excessive stress on connector wire seal sections and deforming them. This compromises seal integrity, allowing rainwater ingress into connectors and causing short circuits. …

In the headlights, due to an inappropriate control program in the headlight control unit, when following closely behind a forward vehicle, a pattern not specified in the safety standards may be projected …

Improper manufacturing control of the passenger-side airbag has resulted in some units with improperly assembled airbag covers. When the passenger-side airbag deploys, depending on the cover attachment position, occupant protection may not …

The coolant air-bleed line has improper routing and may interfere with the engine wiring harness. Continued operation in this condition risks the air-bleed line developing a hole, potentially causing coolant leakage.

The shift cable for the transmission parking lock mechanism may have a damaged sleeve or improperly installed retaining clip due to inadequate work instructions during manufacturing. This can result in the parking …

The braking system has inadequate design, resulting in insufficient front brake hose length. Continued use in this condition causes excessive load on the brake hose ends due to steering angle, leading to …

The brake system has an improper design resulting in insufficient length of front brake hoses. Continued use in this condition causes excessive stress on brake hose ends due to steering angle, leading …

In the combination meter, the control program for the engine oil pressure warning light was not sufficiently reviewed. As a result, the meter cannot receive an abnormal signal when oil pressure becomes …

In medium-duty trucks, insufficient design review of wiring routing tolerances has resulted in interference between wiring on the left frame and peripheral components such as the engine side cover. Continued use may …

The turbocharger lubricating oil supply line has inadequate fastening. During rapid acceleration, internal oil pressure increases, causing stress concentration on the oil seal. This can lead to oil seal degradation and oil …

In the scatter-type warning lights installed on road work vehicles, some units lack grease application on switch contacts due to improper manufacturing of the power switch. Repeated switch operations may result in …

Due to improper software in the headlight control unit, when reversing a vehicle with adaptive headlights illuminated via auto-light function, the cornering light function of the adaptive headlights becomes activated. This results …

Due to improper software in the headlight control unit, when a vehicle is reversed with adaptive headlights activated by the auto light function, the cornering light function of the adaptive headlights becomes …

The driver's seat belt reminder warning sound and warning light do not activate when the driver's seat belt is unfastened while driving at speeds exceeding 10 km/h and not exceeding 20 km/h. …

In the transmission control computer, clutch control during deceleration is improper. When braking firmly to a stop, the clutch connecting the engine and motor may remain disengaged. As a result, power from …

On vehicles equipped with dual-axle leaf suspension at the rear, reaction rod fixing bolts are not tightened to the specified torque due to insufficient tool management controls during fastening. Consequently, bolts may …

The hydraulic motor that maintains the position of the operator cabin on the forklift loader may slip due to air or contaminants entering the hydraulic circuit. As a result, the cabin may …

The three-section rear underrun protection device has insufficient design verification. When installed on vehicles with a total width of 2,000 mm or greater, the effective surface area of both rear sides of …

Cracks and deformation may occur in the tread of rear tires. Continued use may result in abnormal vibration, and in the worst case, tread separation could occur, compromising running stability.

In the combination meter, due to inadequate control program logic, the warning display time for rear seat belt non-use may not meet the legally mandated display duration when the vehicle is started …

Improper manufacturing control of ignition coil high-tension code has resulted in some non-genuine units being installed. Repeated flexing during vehicle operation can cause cracks in the high-tension code. Continued use may lead …

In mechanical automatic transmissions (AGS), the brush material of the oil pump drive motor is inappropriate, causing brush expansion and sliding malfunction under high temperature and high humidity conditions. Continued operation in …

In the navigation system, due to improper control programming, the LCD screen may turn black or freeze when certain operations are performed. As a result, camera footage for rear and left confirmation …

In the fuel system, the fuel pressure/temperature sensor mounting housing attached to the fuel supply pipe has inadequate manufacturing control, resulting in insufficient housing strength in some units. During use, cracks may …

In the vehicle frame of rotary snow removal vehicles, insufficient frame strength may cause cracking in the frame. If use continues in this condition, cracks will progress, and in the worst case, …

Certain drive batteries in PHEV-specification vehicles have internal defects in battery cells, which may result in vehicle fire.

The driver seat belt non-use warning system may not activate even when the driver is not wearing the seat belt due to insufficient structural design of the seating sensor, potentially failing to …

In the engine, the manufacturing process of the water pump cover is improper, causing paint to adhere to the joint pipe press-fit section. As a result, heat from the engine and other …