Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 95 of 355
In the exhaust pipe, the torque specification for the exhaust pipe front assembly work was inappropriate, resulting in some units being fastened at torque values lower than specified. Consequently, vibration during operation …
The mounting nuts of the left and right tail lights to the body have insufficient cleaning treatment during manufacturing, resulting in incomplete removal of cutting oil. The residual cutting oil causes deterioration …
The Powertrain Control Unit contains incorrect programming due to improper program specification instructions. This causes delayed catalyst temperature rise, resulting in emissions that fail to meet standards and degraded fuel economy.
The Powertrain Control Unit contains incorrect programming due to improper program specification instructions. As a result, the SCR monitoring function does not operate correctly, idle stop does not function, and exhaust emissions …
In the electric power steering system, improper routing of electrical wiring has resulted in some units where the wiring is pinched between the suspension frame and underpanel. Due to vibration during driving, …
The switch unit mounted on the center console has improper programming, which may cause a malfunction signal to be input when the ignition switch is turned off. As a result, certain switch …
In the brake pedal of the shovel loader, the spring forming fixture for the brake light switch was set improperly, resulting in some springs with undersized inner diameters. This causes excessive load …
On excavator-loader engine controller wiring, improper routing instructions cause interference between the wiring and hydraulic hoses. This results in wire insulation abrasion and short circuits, causing warning lights to illuminate, and in …
The lock mechanism in the hydraulic camshaft adjuster of gasoline engines has inadequate material properties, resulting in insufficient durability. As the lock mechanism wears, abnormal noise may occur during engine start-up. In …
In the driver assistance system of large tractors, the control program in the driver assistance control unit rewritten under improvement measure (Measure 564) is inappropriate. When a trailer without ABS is connected, …
The rear brake chamber of large trucks has insufficient structural strength. When driving at 80 km/h over lane markings (vibration lines) on expressways, the vibration frequency can cause cracks to develop in …
Some door speaker hole covers were not installed due to improper parts list during manufacturing. As a result, the airbag sensor inside the door may not function correctly during side-impact collisions, potentially …
The selector cable bushing for the automatic transmission is made of inappropriate material, resulting in insufficient strength in some units. The bushing may fracture, preventing proper shift position transmission to the transmission. …
In large trucks, the Driver Assistance Control Unit (DACU3) shutdown program is inappropriate, causing DACU3 to enter restart standby mode when an error is detected during system shutdown phase. As a result, …
The drive shaft dust boot may have insufficient joint strength due to inadequate temperature control during manufacturing. This can cause cracks to develop, leading to grease leakage from inside the dust boot, …
In infant-dedicated vehicles, the positioning of the restraint pipe fastening bolt between the driver seat and rear seat is inappropriate. During sudden braking and similar events, infants may contact this bolt and …
The passenger-side airbag may develop unexpectedly high internal pressure during deployment in high-temperature conditions due to inadequate review of deployment characteristics. This may cause the bag to rupture or the bag-retaining bracket …
The inflator (inflation device) for the passenger-side airbag has inadequate moisture-prevention measures for the gas generant, which may degrade due to repeated temperature and humidity fluctuations. This may cause the inflator container …
The mounting nuts securing the left and right taillights to the body may retain cutting oil due to insufficient cleaning during manufacturing. The residual oil causes deterioration and damage to the taillight …
The passenger seat airbag inflator lacks adequate moisture protection for its gas generant, which may degrade due to repeated temperature and humidity fluctuations. This creates a risk of inflator container rupture during …
The airbag control unit contains a power supply circuit capacitor with inadequate electrical conductivity, resulting in unstable voltage regulation. Consequently, the airbag warning light may illuminate and the airbag and seat belt …
At the brake chamber piping connection, improper selection of the connecting fitting allows the brake piping to deflect significantly under driving vibration and similar conditions. The stress from this deflection can damage …
In vehicles equipped with liquefied petroleum gas (LPG) tanks, improper design of the mounting position may obstruct the outer viewing angle of the rear combination lamp with the bumper body. As a …
In the user software of the digital tachograph, the screen display program is defective, causing the device model designation number of the corresponding digital tachograph to not be displayed on the screen …
The fuel tank cap ventilation has inadequate airflow circuit capacity design. When fuel tank temperature rises due to ambient or engine temperature effects, internal pressure may increase. Opening the fuel tank cap …
The 7-speed DSG automatic transmission mechatronics have insufficient durability due to improper threading on the upper housing. Fatigue accumulation from continuous hydraulic pressure fluctuations in the accumulator can cause cracks in the …
Improper routing of the battery harness allows interference between the transmission mount and the harness, causing insulation damage. This can result in harness short-circuiting, blown fuses, illumination of warning lights, and in …
On the braking device of the trailer's first axle, the clearance between the connecting fitting of the air hose connected to the brake chamber and the air tank is inadequate. When wheels …
The regenerative braking program in the powertrain control unit is inappropriate, which may cause an extended delay in transition to friction braking when regenerative braking fails. This may not meet the safety …
In battery-powered forklifts, the accelerator pedal throttle opening sensor uses an incompatible adhesive to fix the internal magnet to the sensor, resulting in weak adhesion. Repeated operation of the accelerator pedal can …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.