Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 11 of 175
In the integrated brake unit, inadequate manufacturing controls have resulted in foreign matter adhering to the motor sensor circuit board. Additionally, insufficient design review of the contact pin length causes noise generation …
On large wing-body vehicles, the mounting bracket that connects the chassis frame to the cargo bed was insufficiently designed in terms of attachment position. As a result, some units were assembled with …
In the high-voltage battery cell modules, improper manufacturing caused the positive electrode sheet cut edges to bend, which can damage the separator. This may result in internal short-circuiting within the cell module, …
The shaft connecting the brake pedal to the brake booster may not be assembled to specification due to improper equipment settings during manufacturing. This can cause the fasteners at the joint to …
The crimp load setting for the clamp ring that secures the inflator and airbag in the side curtain airbag is improper, resulting in excessive crimping force that may cause insufficient clamp ring …
The rear brake caliper mounting bolts may be insufficiently tightened due to improper installation procedures. Continued use in this condition may cause the bolts to loosen, resulting in noise during braking or …
In the Parking Assist Unit, improper signal processing from wheel speed sensors can cause discrepancy between the distance to obstacles detected by ultrasonic sensors during reverse and the travel distance calculated from …
In the Cross Traffic Alert function, one of the driver assistance system features, the control program of the parking control unit is inappropriate, which may cause unintended interruption of operation. As a …
The transmission electrical wiring has improper routing design, causing the connector sealing section to deteriorate over time due to heat from the exhaust manifold and rainwater exposure. This compromises seal integrity, allowing …
Due to an inappropriate control program in the engine control unit, a malfunction occurs in the variable valve mechanism (Camtronic). When cylinder deactivation is activated, the air-fuel ratio correction control does not …
Certain propeller shafts have inadequate component manufacturing controls, resulting in CV joints that transmit power to the rear wheels being insufficiently greased. This can cause internal damage due to inadequate lubrication, potentially …
In the axle of a shovel loader, improper heat treatment of the axle shaft results in insufficient hardening depth that does not meet design specifications, causing some shafts to have insufficient strength. …
The adjustment units of the variable valve timing systems on the intake and exhaust sides have bolts of insufficient strength, which may fracture. This can cause the system to malfunction, resulting in …
High-voltage batteries may contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in thermal battery malfunction and fire.
Some high-voltage batteries contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in thermal battery anomalies and fire risk in severe cases.
The center lock mechanism that secures the wheel to the axle contains units that were improperly manufactured and do not meet specifications. Continued use in this condition may cause the center lock …
In the front suspension, the adhesion of paint to the coil spring steel is insufficient, resulting in easy paint film peeling when sand or gravel is trapped, leading to accelerated corrosion. Continued …
The striker that holds the cargo bed side sliding door in the closed position on van-type trucks has insufficient strength due to inadequate vibration analysis during design. Consequently, cracks may develop in …
In the rear combination lamp of low-floor dump trucks, insufficient consideration was given to lamp placement. During operation, ice and snow kicked up by the rear wheels can accumulate and solidify in …
In the engine oil preheating device power harness, due to insufficient work instructions, some units have inadequate insulation processing on terminals. This can result in insulation breakdown due to carbonization of materials …
In MC4 connectors used for solar panel connection, improper manufacturing processes result in incomplete terminal installation on some units. This can cause contact failure, leading to connector fusion, and in worst cases, …
In the parking brake air hose of crane vehicles, the crimping process of the air hose connector fitting is improper, which may cause damage to the rubber at the hose crimping section. …
In front drive shafts, due to insufficient production equipment management, some wheel-side joint components are not assembled. Continued use in this condition may cause damage to the joint, resulting in loss of …
In the intermediate shaft, insufficient examination of the press-forming process has resulted in cracks at the joint portion during molding in some units. Consequently, cracks may progress and fracture during use, potentially …
In hybrid vehicles, the brake actuator control computer may have insufficient control program design, making it unable to properly adjust brake hydraulic pressure during cornering braking. As a result, braking force may …
The diesel engine exhaust gas recirculation (EGR) module may experience coolant leakage due to manufacturing process variations. When this occurs, soot contained in the exhaust gas mixes with coolant and accumulates inside …
The inflator (inflation device) of the driver-side airbag may experience degradation of the gas generant when subjected to repeated large temperature fluctuations in high-humidity environments. As a result, the inflator container may …
High-voltage battery cell modules may experience internal short circuits due to improper manufacturing. In the worst case, this may result in fire.
The center lock mechanism that secures the wheel to the axle has been manufactured improperly and does not meet specifications. Continued use in this condition may result in center lock failure, and …
Due to insufficient work instruction management for the fuel gauge harness, some vehicles have sustained damage to the harness during vehicle floor processing. As a result, fuel level information may not be …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.