In charging plugs for electric forklifts, terminal geometry is inadequate, causing terminal deformation during use. Continued operation prevents the plug from seating fully, resulting in poor terminal contact. In the worst case, …
小松 FB09H 2006–2009
小松 FB09ML 2006–2009
小松 FB10 2006–2009
小松 FB10ML 2006–2009
小松 FB13ML 2006–2009
+9 more
The return pipe attachment section of the fuel pump lacks sufficient strength, which may result in cracks during use. Continued operation could cause crack propagation and fuel leakage.
Citroen C2 2001–2007
Citroen C3 2001–2007
Citroen C3 Pluriel 2001–2007
Citroen C5 2001–2007
Peugeot 1007 2001–2007
The hose connecting the fuel pump and fuel filter may have an improperly positioned clip due to manufacturing defects, resulting in inadequate fastening. Continued use may cause the hose to detach, preventing …
Ducati 1198S 2009
Due to improper geometry of the brake cable guide, vibration may cause the main harness to interfere with the brake cable guide. Continued operation in this condition may damage the main harness, …
Komatsu WA30-6 2008–2009
Komatsu WA40-6 2008–2009
Komatsu WA50-6 2008–2009
In electric forklifts, improper routing of the battery cable can cause the battery cable plug to become disconnected during operation. If use continues in this condition, the plug may develop poor contact, …
小松 FB09H 2006–2009
小松 FB09ML 2006–2009
小松 FB10 2006–2009
小松 FB10ML 2006–2009
小松 FB13ML 2006–2009
+6 more
Certain rear wheel brake hoses are installed at improper angles, which may cause the brake hose to contact and be damaged by the tire. In the worst case, rear wheel braking may …
Kawasaki ZRX 1200R 2008
During the brake fluid filling process in vehicle assembly, improper air line layout in the filling equipment allows excessive moisture to enter the hydraulic brake circuit in some vehicles. During frequent brake …
Kawasaki 45ZV 2008–2009
Kawasaki 50ZV 2008–2009
Kawasaki 55DV 2008–2009
Kawasaki 60ZV 2008–2009
Kawasaki 60ZV-2 2008–2009
+5 more
The vibration-damping rubber characteristics of the crankshaft pulley are inappropriate, causing the fuel pump camshaft to vibrate at high engine speeds. Continued operation in this condition may result in camshaft fracture, loss …
Kawasaki 65ZV 2005–2008
コべルコ LK190Z-5 2005–2008
In vehicles equipped with a regenerative control-type DPF, brake air tubes, parking brake cables, and transmission cables routed near the exhaust manifold may reach high temperatures. Continued operation in this condition can …
Nissan Condor 2004–2006
The core wire material of the auxiliary drive belt for all-wheel-drive vehicles is inappropriate, which may cause the belt to break during use. As a result, auxiliary components may not be driven, …
Nissan Cube 2008–2009
The fuel return hose installed in the fuel system has insufficient clamp band tightening force. When fuel freezes in low temperatures and internal pressure rises, the hose may detach. This can result …
Kubota GV760 2007–2009
Kubota GV850 2007–2009
Kubota GV950 2007–2009
Kubota GVK760 2007–2009
Kubota GVK850 2007–2009
+4 more
In the steering mechanism, improper welding of the handlepost may cause cracks to develop at the weld. If use continues in this condition, crack propagation may prevent the handlepost from being properly …
Kubota 2500 MZ 2007–2009
Kubota GV500 2007–2009
Kubota GV550 2007–2009
Kubota GV600 2007–2009
Kubota GV650 2007–2009
+17 more
On the rear axle of certain large cargo vehicles (rear-drive, 3-axle configuration), insufficient strength margin for the operating environment may cause cracks to develop. Continued operation in this condition risks crack propagation …
Nissan ― 1994–2009
The acorn stud bolt connecting the brake caliper bracket and front brake reaction link has inadequate design, which may cause the bolt to loosen during use. Continued operation in this state risks …
Harley-Davidson FLSTSB 2008–2009
In the fuel injection system, improper machining during fuel supply pump manufacturing can cause internal cracking in the pump, leading to fuel leakage that mixes into engine oil. If operation continues in …
Mitsubishi Mitsubishi Motor Grader 2008–2009
The axle shaft has inadequate strength due to improper heat treatment. Continued use may result in axle shaft fracture in worst-case scenarios, potentially causing loss of vehicle mobility.
Hino Hino Super Dolphin 2003–2006
Hino Hino Profia 2003–2006
In automatic transmission vehicles, the braking system has insufficient vacuum capacity. Frequent brake operation causes a reduction in brake assist force, which in the worst case may result in increased braking distance.
Alfa Romeo 159 2007–2008
Alfa Romeo Alfa Brera 2007–2008
The terminals in the electrical wiring connector portion of the left combination lamp (tail light, brake light, and turn signal) bulb holder may be deformed. This causes insulating material to form on …
Nissan Dualis 2007
On vehicles equipped with Intelligent Key, a gap exists between the handle base and handle cover on the exterior handles of the driver and front passenger doors. When opening the door, the …
Nissan Dualis 2007
In the fuel injection system, improper machining during manufacturing of the fuel supply pump causes internal cracks in the pump, allowing fuel to leak and mix with engine oil. Continued operation in …
ニッセキ HTR265L 2008–2009
ニッセキ HTR300M 2008–2009
In the fuel injection system, improper machining during manufacture of the fuel supply pump causes cracks to develop inside the pump, allowing fuel to leak and mix with engine oil. Continued operation …
T C M FD240-4 2008–2009
T C M JR180-3 2008–2009
T C M MR450 2008–2009
In the fuel injection system, improper machining during manufacture of the fuel supply pump causes internal cracks in the pump, resulting in fuel leakage that mixes with engine oil. Continued operation in …
カトウ Kato KR-70H Rafter 2008
In the fuel injection system, improper machining of the fuel supply pump during manufacturing causes cracks to develop inside the pump, allowing fuel to leak and mix with engine oil. Continued operation …
Mitsubishi Fuso 2006–2008
Mitsubishi Fuso Aero Ace 2006–2008
On vehicles equipped with Intelligent Key, the exterior door handles for the driver and front passenger seats have a gap between the handle base and handle cover. The handle may catch and …
Nissan Dualis 2007–2008
The brake air tank bracket has insufficient strength, which may cause cracks to develop. In the worst case, the bracket may fracture, damaging the brake air tube and resulting in reduced braking …
Nissan - 2005–2008
In the engine compartment, the hydraulic fluid pipes that operate the convertible top lack sufficient heat resistance. Exhaust manifold heat can cause fine cracks to develop in these pipes. Continued use may …
Ferrari F430 Spider 2005–2007
Ferrari F430 Spider F1 2005–2007
On vehicles equipped with automatic opening/closing tailgate, the seal material in the tail lamp section is inadequate, allowing water to infiltrate the vehicle interior during heavy rain or high-pressure washing. Continued use …
Mercedes-Benz ML350 2008–2009
Mercedes-Benz ML550 4MATIC 2008–2009
Mercedes-Benz ML63 2008–2009
In medium-duty trucks (fire engines) equipped with ABS (Anti-lock Braking System), insufficient clearance exists between the water pump flow adjustment rod and the fuel and air piping, causing potential interference. Continued operation …
Mitsubishi Fuso Fighter 1995–1998
In the fuel injection system, improper machining of the fuel supply pump during manufacturing causes internal cracks in the pump, allowing fuel to leak into the engine oil. Continued operation in this …
Mitsubishi Fuso 2007–2008
In the steering system, one of two bolts securing the knuckle arm to the knuckle has inadequate strength due to improper heat treatment. This bolt may fracture prematurely, and in the worst …
Hino Hino Blue Ribbon II 2005–2006