Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 115 of 175
In the steering system, one of the two bolts securing the knuckle arm to the knuckle may have insufficient strength due to improper heat treatment. This can result in premature bolt failure, …
On route buses, due to improper wheel turning angle, when studless tires are installed and the steering wheel is turned to maximum while passing over a step, or when the vehicle is …
On route buses and similar vehicles, due to improper tire toe angle, when studless tires are installed and the steering is turned to maximum while crossing a step, or when the vehicle …
In agricultural tractors, improper routing of the main harness may cause interference with the power steering hose, frame, and engine heat shield. Continued operation in this condition risks damage to the harness …
Battery wiring routing may be altered due to improper installation instructions during vehicle assembly, causing interference with the torque converter oil dipstick and hydraulic hoses. Continued operation in this condition may result …
In forklift main harnesses, improper assembly work instructions have resulted in some harnesses not being properly secured. Continued operation in this condition may cause the harness to be pinched and damaged between …
The front wheel brake cable length is inappropriate, causing the cable to bend at the cable clamp during front fork compression and extension while driving. Continued use may result in breakage of …
In the electric parking brake equalizer (device that distributes parking brake operating force evenly to both wheels), some units lack the cable retaining clip. This may cause uneven parking brake engagement.
On the front wheels of asphalt finishers, some mounting nuts have insufficient fastening torque. If operation continues in this condition, the nut may loosen and the wheel may separate.
Some front axle shafts have insufficient thickness. When excessive load is applied to the front wheels, cracks may develop in the shaft. Continued use could result in shaft breakage, which in worst …
The combination of contact structure and grease inside the brake light switch is inappropriate, which may cause insulating material to form on the contact points due to arcing. Continued use may increase …
The hub outer bearing installed on the driven axle of the crane trailer has insufficient strength due to defective heat treatment during manufacturing, which may cause the bearing to fail. Continued use …
Improper routing of the front brake hose may cause contact between the brake hose and front tire during operation. Continued use in this condition could result in brake hose damage, potentially leading …
The fuse capacity for the air conditioning heat exchanger cooling fan is inappropriate. If the fan locks or rotates excessively due to external factors such as mud buildup, the fan motor may …
The brake light relay has insufficient capacity, and frequent brake operations may cause damage to the relay contacts. Continued use in this condition could result in contact adhesion, causing the brake light …
The engine intake air duct is made of inappropriate material, causing it to shrink due to engine heat and loosen the fastening at the resonator (intake noise suppression device) connection. Continued use …
Some vehicles have improperly positioned fuel filters, causing excessive stress on the fuel pipe connecting the fuel filter to the fuel pump. Continued use may result in cracks developing in the plastic …
The plastic nuts used to attach the fuel pump to the top of the fuel tank may have received improper heat treatment during manufacturing. Repeated temperature cycling can cause cracks to develop …
In the forklift braking system, improper work instructions during assembly may cause the brake hose and working hydraulic piping to interfere with each other. Continued operation in this condition can result in …
The brake booster body has improper crimping with insufficient crimp strength in some units. When the brake pedal is pressed firmly, the crimp may fail, preventing brake pedal force from being transmitted …
The fuel low-pressure pipe inside the engine head cover has insufficient precision control at the joint surface with the injector, causing the bolt securing the pipe to loosen. This allows fuel to …
In the steering system, the spool valve that controls the internal pressure of the power steering hydraulic pump to remain below a specified value has some units with narrow clearances. When foreign …
In rear drum brakes, some vehicles have insufficient fastening torque on the brake drum backplate mounting bolts. If operation continues in this condition, the mounting bolts may loosen and cause abnormal noise, …
In the gear section that operates the supply pump, bearing lubrication method and bearing case material are inadequate, causing bearing damage in some units. This results in breakage of the supply pump …
On turbocharged vehicles, the oil feed pipe supplying oil to the turbocharger has improper routing and corrosion protection. When exposed to salt water from de-icing salt in snowy regions, the pipe may …
During propeller shaft manufacturing, rust-preventive oil may adhere to the flange joint surface of the intermediate joint. Repeated abrupt clutch engagement and disengagement can cause the flange fastening bolts to loosen. This …
The valve in the piston section of the brake master cylinder has an improper shape, which may cause the valve to become pinched between the valve rod and piston during brake operation. …
In vehicles equipped with compressors for refrigeration/freezing units, the regeneration control program for the regenerative DPF is inappropriate, causing service brake air tubes, parking brake air tubes, or center brake cables routed …
Improper exhaust pipe installation method results in misaligned joints between the exhaust pipe and DPF (Diesel Particulate Filter) during assembly. This causes high stress in the exhaust pipe bellows section, leading to …
In low-floor all-wheel-drive vehicles, improper front axle structure and inadequate cleaning procedures during manufacturing allow foreign material inside the axle to enter the reduction gear bearings, potentially causing reduction gear failure. Continued …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.