Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 14 of 175
In coupling devices for large tractors, the lock guard shape that prevents misconnection is inadequate. When connecting a tractor and trailer at mismatched heights, the lock guard may not function properly, resulting …
On the two-axle coupler of large tractors, the lock guard (misconnection prevention component) shape was redesigned to improve manufacturing process efficiency; however, the new shape is inadequate. When coupling operations are performed …
On large tractor coupling devices, the shape of the anti-misconnection prevention component (lock guard) is inappropriate. When coupling operations are performed with the tractor and trailer at mismatched heights, the lock guard …
On large tractor coupling devices, the lock guard shape designed to prevent incorrect coupling is inadequate. When coupling operations are performed with misaligned heights between tractor and trailer, the lock guard does …
In the coupling device of large tractors, the lock guard shape that prevents incorrect coupling is inappropriate. When coupling operations are performed with misaligned heights between tractor and trailer, the lock guard …
The three fastening nuts securing the power line to the 12V battery fuse box lack adequate torque during manufacturing and may loosen during use. This can impair vehicle power supply, potentially causing …
Rear inner shafts were assembled in an insufficiently cooled state due to inadequate maintenance of the heat treatment equipment. This results in insufficient strength, causing the inner shaft to fracture during driving, …
In large-capacity tour buses, some vehicles were shipped without the steering wheel fixing bolt installed due to inadequate fastening procedure. This may cause the steering wheel to separate from the shaft.
The oil filter case material used in the oil filter, which filters the engine lubricating oil, differs from the specification. Consequently, the case may rupture under internal lubricating oil pressure, and scattered …
The vehicle control module contains incorrect settings due to improper work instructions. As a result, the ESS (Emergency Braking Indicator Light) does not operate.
The brake hose installed between the brake fluid reservoir tank and brake master cylinder is made of inappropriate material, which may chemically react with the brake fluid inside the hose. The brake …
In the front-wheel suspension systems of light-duty trucks, insufficient durability of the suspension crossmember can cause cracks to develop at the upper mount rubber attachment point of the front leaf spring. Continued …
In trucks equipped with 4V20 engines, the exhaust brake control program in the engine ECU is inappropriate, causing the exhaust brake drive gear to strike the stopper at speeds exceeding design specifications. …
In the integrated brake unit, inadequate manufacturing control has resulted in foreign matter adhering to the motor sensor circuit board in some units. This causes electrical contact failures, resulting in brake warning …
In certain excavator loaders, non-genuine bearings have been installed in the brake linkage bearings. Repeated brake operation can cause these bearings to seize, making the brake linkage difficult to move. In worst-case …
In the front suspension, bolts fastening the upper control arm to the knuckle may be damaged due to improper tightening during assembly. This can cause bolt fracture, resulting in failure to properly …
The power liftgate control module on the back door has inadequate waterproof design. Rainwater and other moisture can travel through the rear gate opening and intrude into the connection terminal section of …
High-voltage batteries may contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in battery thermal anomalies and fire.
High-voltage batteries may contain improperly manufactured battery modules. This can cause internal short circuits in the battery modules, potentially resulting in thermal battery anomalies and fire.
In the Collision Mitigation Braking System (FCM), the front radar ECU control program is inappropriate. When the front camera temperature rises due to parking in direct sunlight, if the FCM temporarily stops, …
Front and rear window glass may have insufficient adhesion due to inadequate cleaning during manufacturing. This can result in water infiltration at glass bonding surfaces and wind noise during driving. In the …
In the brake operating simulator of the electric servo brake system used as a replacement part, improper manufacturing processes may allow assembly oil used during production to infiltrate the pressure sensor. Consequently, …
On large refrigerated trucks, the work instruction for the left front U-bolt securing the chassis frame to the subframe was inappropriate, resulting in some vehicles having insufficient clearance between the vehicle-side wiring …
The gateway module that detects brake pad wear has improper programming, which may prevent detection of brake pad wear condition and fail to notify the driver of the wear status.
Agricultural tractor front suspension ball joints may be improperly assembled and not correctly attached to the knuckle housing. Continued operation in this condition can result in premature ball joint wear or knuckle …
The side airbags installed on the left and right front seats may inadvertently deploy in frontal collisions and similar impacts where such airbags are not required, due to improper programming of the …
Forklift steering axles may have non-standard dimensions due to improper machining during manufacturing. When the steering wheel is turned to maximum lock in the left direction, the left rear wheel may interfere …
The control program in the CAN gateway, which is the communication control device between in-vehicle control units, is inappropriate, which may result in communication malfunction among in-vehicle control units. As a result, …
Some aluminum wheels have improper machining at the wheel mounting surface, resulting in insufficient clamping face dimensions. This causes hub nuts to bottom out with insufficient clamping force. Continued operation in this …
In wing-equipped vehicles, improper manufacturing control of the wing power harness routing causes the wing power harness to press against the chassis harness. This can cause the unprotected portion of the chassis …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.