Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 19 of 175
The fuel supply module flange in the fuel tank of the fuel system has improper component design. When ambient temperature is high and low-quality fuel is used, excessive current flow can cause …
The instrument cluster program for the brake booster warning system is inadequate. When the brake booster malfunctions, the warning light does not illuminate. After the warning message is displayed, an incorrect warning …
In the steering system, due to inadequate manufacturing control, some vehicles were assembled with the steering shaft not fully inserted to the specified position at the gearbox connection. This results in insufficient …
In the electric steering system of dolly-equipped ball trailers, due to improper design of the control unit's control program, the electromagnetic valve fault monitoring function may activate when power is temporarily interrupted …
In the main fuse box wiring within the engine compartment, improper assembly during manufacturing has resulted in terminal point nuts not being tightened to the specified torque. Consequently, vibration during operation can …
In 12V and 48V ground wiring located in the engine compartment and undercarriage, improper assembly during manufacturing has resulted in some vehicles where the nut at the body ground terminal point is …
The 48V ground wiring in the engine compartment may have improper assembly at the factory, with the nut at the body ground terminal point not tightened to the specified torque. This can …
Certain rear suspension leaf springs have insufficient strength due to improper manufacturing equipment settings. As a result, the leaf spring may fracture when driving on rough roads, potentially causing a drop in …
On large trucks, the tailpipe material bonded to the muffler is inappropriate. Continued use with de-icing agents remaining at the joint can cause corrosion and fracture of the tailpipe at the joint, …
In alternators on vehicles without idle stop function, the grease sealed within the pulley's internal mechanism (one-way clutch) had insufficient heat resistance. During use, the grease degrades from heat, causing wear and …
The coolant hose connection between the engine and radiator has inadequate design. Under high-load operation (such as circuit driving), coolant may leak from the connection point. In the worst case, coolant contact …
In the CVT (continuously variable transmission), fastening of the bolts securing the drive plate to the torque converter may be improper. If operation continues in this condition, the bolts may loosen and …
On agricultural tractor axles and transmissions, improper painting methods cause wheel bolts and nuts, as well as bolts and nuts assembled to the transmission after painting, to loosen. Continued operation in this …
In the insulation (heating) apparatus of refrigerated transport vehicles, insufficient design verification resulted in inadequate clearance between the refrigeration unit piping and the cabin rear surface. Due to sagging of the cab …
In the dashboard, due to inadequate maintenance of the manufacturing equipment, some passenger-side airbag guide channels are not welded to the dashboard according to specifications. As a result, when the airbag deploys …
The traction battery ECU software is inadequate, which may prevent early detection of drive battery anomalies. If an anomaly progresses undetected, it could potentially result in vehicle fire.
In the rear light fixture, wiring assembly position variation causes the vibration-damping pad to press the wiring against the fixture case interior, risking wiring damage. Continued operation may result in wiring breakage, …
The cooling fan motor circuit has improper design, resulting in an unnecessary diode being installed. When the fan motor idles, reverse voltage generated is applied to the diode, causing it to overheat, …
① The clutch carrier of the alternator pulley may have insufficient strength due to molding process defects, preventing proper transmission of engine power to the alternator and causing charging failure. ② Due …
The coating material of the side brake auto-adjustment bolts in the left and right rear brake calipers is inadequate, causing stick-slip phenomena that result in uneven side brake braking force between left …
In the current rectifier module of the voltage converter (DC-DC converter), the internal component structure is inadequate. When this module fails during use due to manufacturing variations and other factors, a short …
On agricultural tractor wheel bolt and nut fastening points, due to improper manufacturing methods, the bolts and nuts may loosen. If work continues in this condition, the bolts and nuts may detach, …
In center-type parking brake systems installed on agricultural chemical sprayers, the welding of pins attached to the brake backplate may be inadequate. If the vehicle is operated with the parking brake engaged, …
In the work equipment controller of the shovel loader, due to an improper program, if the power supply voltage drops during the self-diagnosis routine that automatically initiates after the key is turned …
In diesel engines, the exhaust gas recirculation (EGR) module has insufficient durability considerations. With age, coolant may leak from the module. When this occurs, soot contained in exhaust gases mixes with the …
In large hybrid transit buses, due to inadequate hybrid control programming, the supply pump sliding surfaces may experience poor lubrication from foreign matter in the fuel during engine start, causing wear. Continued …
In large hybrid transit buses, the hybrid control program is inappropriate, causing the supply pump sliding surfaces to experience poor lubrication due to contaminants in the fuel during engine start, resulting in …
The fuel pump has an improperly positioned vent hole for releasing fuel evaporative gases. In low-pressure environments such as high-altitude areas, or during congested driving in high-temperature conditions, fuel evaporative gases may …
The impeller (resin-molded fan wheel) in the fuel pump may swell and deform due to improper manufacturing when exposed to fuel. As a result, the impeller can contact the pump housing, causing …
Due to inappropriate material selection in the fuel hose, thermal degradation may progress. This can result in decreased sealing integrity at connection points, potentially causing fuel leakage.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.