Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 21 of 175
The intermediate shaft has improper assembly work during vehicle assembly, resulting in bolts fastening to the steering gear not being tightened to specification torque. Continued use may cause bolt loosening, and in …
In the front suspension, improper assembly work during vehicle production has resulted in some units where the bolt and nut fastening the upper arm ball joint to the steering knuckle are not …
Plastic coolant pipes, which are part of the coolant circulation circuit, were manufactured using a material with low heat resistance. When coolant circulation stops, such as due to water pump failure, these …
In the parking brake of agricultural chemical spray vehicles, inadequate manufacturing control of the hook and gear that hold the lever in the fixed position results in insufficient strength of the hook …
The permanent-magnet retarder (auxiliary brake) on the rear axle is actuated by air pressure. A design error in the connector terminal configuration of the chassis harness connected to the retarder harness results …
In trailers equipped with lift-axle functionality, insufficient strength analysis resulted in inadequate strength of the clamping plate that secures the lift air spring of the lift device, which may fracture and cause …
The trailing arms in the front and rear suspension have insufficient corrosion resistance due to inadequate material selection during design. Extended use results in corrosion at the arm joints, causing cracking accompanied …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in low resin density, causing swelling from fuel exposure. This can cause …
The fuel pump impeller (plastic rotor) may have been molded under improper conditions, resulting in low resin density. This causes the impeller to swell and deform when exposed to fuel, potentially contacting …
The electric coolant pump for the air conditioning system has an inadequate design for venting internal negative pressure, allowing moisture to enter the electrical connector inside the pump and potentially causing short …
In the braking system, the front wheel brake hose was not properly installed in the correct position due to improper assembly work on the vehicle body. As a result, the hose contacts …
In the 48-volt hybrid system, improper tightening of the positive terminal and ground cable terminal may result in poor electrical contact. This can cause hybrid system malfunction warnings to be displayed, and …
In semi-trailer air suspension systems, inappropriate material selection for components comprising the bellows (air spring) can result in excessive suspension travel range under certain road conditions. Impact from the bump rubber inside …
The coolant pump installed in diesel engines has an improperly designed bearing seal, allowing coolant to ingress into the vacuum-controlled circuit, causing malfunction of related components. This results in engine warning light …
Certain front axle electrical wiring installations have improper cable routing that causes interference with the auxiliary oil cooler or auxiliary radiator. This results in protective covering abrasion and wire exposure, leading to …
On the rear wheel brake calipers, tightening was performed without noticing the breakage of the fastening tool, resulting in some bolts not being tightened to the specified torque. Vehicles with torque below …
In large and medium-duty trucks and large buses, the on-board tool kit configuration is inadequate, and the wrench tool for emergency parking brake release is not included. Consequently, when the parking brake …
In the braking system, the damper between the left front wheel brake disc and wheel hub is excessively thick, causing insufficient contact between the wheel hub and brake disc, resulting in uncertain …
The fuel return line design in the fuel system of engine-powered forklifts and shovel loaders is inadequate, resulting in insufficient strength in some units. Repeated engine start-stop cycles in this condition can …
In the steering system, some units have insufficient strength in the spring pin that secures the spline mechanism of the steering wheel. Continued use may result in shearing of the pin when …
Certain side airbags mounted on the front seat backrests have protruding rivet core shafts at the bracket attachment points. During side airbag deployment, the airbag may contact and tear on the protruding …
Due to improper programming in the body control module, if brake fluid pressure in the ABS does not bleed off, the brake lamp may remain illuminated even when braking is not applied.
Improper torque specifications for through bolts in the starter can cause the bolts to loosen over time, resulting in misalignment of internal components and reduced starter output. Continued operation may lead to …
(2) The rear left seat belt buckle has an inadequate retention structure, which can cause it to fall inside the seat, preventing seat reclining operation. If reclining is attempted in this condition, …
In MT (manual transmission) vehicles, the meter panel design is inappropriate, lacking a display device to indicate the automatic control state of the driving headlight (high beam) to the driver. Therefore, it …
The power conversion device (inverter) has an improper control program. When the push-button start is turned on shortly after being turned off, the inverter may fail to activate. This prevents engine restart …
(1) In the transmission control computer, due to an inappropriate control program, when firmly applying the brake during gear shifting or engine restart from EV driving mode, the engaged clutch may not …
In the engine, the manufacturing process of the right-side crankcase cover is defective, causing paint to adhere to the sealing plug press-fit section. Due to engine heat, the retention force of the …
Due to inadequate strength analysis of the exhaust pipe mounting bracket in the wheel carrier noise prevention device, the exhaust pipe resonates at specific engine speeds, which may cause cracks to develop …
In trailers equipped with lift axle functionality, the clamping plate securing the lift air spring of the lift device may fracture due to insufficient strength, risking detachment of lift device components.
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.