Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 32 of 173
In the rear suspension mechanism, the nuts securing the suspension arms are made of inappropriate material, which may cause cracks to develop in these nuts during vehicle operation. As a result, loosening …
The alternator installed in 4-cylinder gasoline engines has improper idle-state charging control, causing rectifier diodes to overheat and fail, resulting in warning light illumination and charging malfunction that can cause engine stalling. …
In the parking brake of excavators and loaders, improper assembly procedures cause the hydraulic cylinder yoke to interfere with the parking brake lever during assembly, damaging the internal plate. Repeated operation and …
Brake calipers may develop corrosion on the piston sliding surface due to inadequate metal surface treatment, which can be accelerated by de-icing agents. The resulting corrosion creates resistance that impairs piston retraction, …
Due to inappropriate instrument panel software, the rear seat belt non-wearing warning display does not activate when ignition is turned on, and the seat belt non-wearing warning display and warning sound do …
In the steering system, improper bolt torque management during manufacturing for fasteners connecting the steering column to the steering gearbox results in some bolts not being properly tightened. Consequently, these bolts may …
In the electric parking brake system, the cable terminal connecting to the drive motor has insufficient strength. When the parking brake is engaged before the vehicle comes to a complete stop, the …
The fuel pump impeller (resin rotor) may have reduced resin density due to improper molding conditions, causing it to swell and deform when exposed to fuel. This can cause the impeller to …
The low-pressure fuel pump fuse rating is improperly set. During engine start preparation, the fuse may blow due to insufficient capacity, causing the low-pressure fuel pump to fail and preventing engine start.
In the electrical system, due to improper programming of the engine control unit and power electronics, false error detection may cause the engine warning light to illuminate during driving, and in the …
The right front lower arm forging in the suspension system is improperly processed on some vehicles, resulting in insufficient strength. Consequently, the lower arm may fracture during operation, and in the worst …
Certain fuel hoses connecting the fuel pump and fuel injector were manufactured with improper inner diameter. This results in insufficient sealing at the hose connection, creating the potential for fuel pressurized by …
In articulated buses: (1) Air spring piston attachment bolts mounted on axles are not tightened to specified torque in some vehicles. During use, these bolts may loosen and the piston may detach. …
In articulated buses, (1) air spring piston attachment bolts fitted to the axle are not tightened to the specified torque in some units. Consequently, these bolts may loosen during use and the …
In articulated buses: (1) Air spring piston mounting bolts installed on axles are not tightened to the specified torque. During use, these mounting bolts may loosen and the piston may detach. (2) …
The driver-side airbag inflator has inadequate desiccant protection, allowing the gas generant to absorb moisture. Repeated moisture absorption and drying cycles during use may prevent proper deployment upon airbag activation in a …
The engine control unit has improper settings for abnormality judgment in the engine control program. Consequently, accelerator operations during acceleration/deceleration and shift operations via manual mode may be incorrectly recognized as inappropriate …
The in-tank unit fuel pump has inadequate clearance design between the resin impeller and cover. When fuel temperature rises, the resin impeller deforms and may contact the cover. This can cause fuel …
The driver-side airbag inflator lacks adequate moisture protection, allowing the gas generant to absorb moisture. Repeated moisture absorption and drying during use may prevent proper deployment during airbag activation in a collision, …
At the vehicle assembly plant, improper installation procedures for the fuel hose have resulted in some units being installed with inadequate clearance between the fuel hose and the intake pipe or engine …
The front brake master cylinder return spring may have insufficient spring tension due to inadequate verification during manufacturing. After brake operation, insufficient spring force may prevent the piston from returning to its …
In gasoline engines, due to improper manufacturing processes at the supplier, cracks have developed in some engine blocks. During use, these cracks may worsen, causing engine oil leakage. In the worst case, …
In the airbag electrical circuit, improper manufacturing instructions during harness production result in the airbag computer wiring not being properly connected to the connector. Consequently, if the vehicle collides while the passenger …
In the driving support system, the forward collision mitigation control program in the driving support ECU is inappropriate, and may recognize highway tunnel lighting as forward-moving objects. This can cause warning sounds …
In the driving support system, the forward obstacle collision mitigation control program is inappropriate, and may recognize lighting in highway tunnels as forward-moving objects. As a result, a warning sound may sound …
In brake calipers, improper metallic surface treatment of the piston sliding surfaces can result in corrosion. This corrosion creates resistance in the sliding surfaces, causing poor piston retraction in the caliper, and …
Inadequate sealing work at panel joints on the left and right footwells of the front seats allows rainwater to enter the cabin. This can cause flooding of the underbody, leading to corrosion …
In the steering shaft, improper use of manufacturing equipment results in some units having an oversized bearing bore hole for the universal joint press-fit. Consequently, play can develop in the steering operation …
In the collision avoidance support system (pre-crash safety system), the pre-crash brake assist control program is inappropriate. When a vehicle with potential collision ahead is detected, the alarm and warning display operate …
The side stand has inadequate welding between the pivot point of the movable arm (side stand arm) and the leg portion. This welding defect cannot withstand the vehicle's weight during parking, causing …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.