Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 34 of 175
In gasoline engines, due to improper manufacturing processes at the supplier, cracks have developed in some engine blocks. During use, these cracks may worsen, causing engine oil leakage. In the worst case, …
In the airbag electrical circuit, improper manufacturing instructions during harness production result in the airbag computer wiring not being properly connected to the connector. Consequently, if the vehicle collides while the passenger …
In the driving support system, the forward collision mitigation control program in the driving support ECU is inappropriate, and may recognize highway tunnel lighting as forward-moving objects. This can cause warning sounds …
In the driving support system, the forward obstacle collision mitigation control program is inappropriate, and may recognize lighting in highway tunnels as forward-moving objects. As a result, a warning sound may sound …
In brake calipers, improper metallic surface treatment of the piston sliding surfaces can result in corrosion. This corrosion creates resistance in the sliding surfaces, causing poor piston retraction in the caliper, and …
Inadequate sealing work at panel joints on the left and right footwells of the front seats allows rainwater to enter the cabin. This can cause flooding of the underbody, leading to corrosion …
In the steering shaft, improper use of manufacturing equipment results in some units having an oversized bearing bore hole for the universal joint press-fit. Consequently, play can develop in the steering operation …
In the collision avoidance support system (pre-crash safety system), the pre-crash brake assist control program is inappropriate. When a vehicle with potential collision ahead is detected, the alarm and warning display operate …
The side stand has inadequate welding between the pivot point of the movable arm (side stand arm) and the leg portion. This welding defect cannot withstand the vehicle's weight during parking, causing …
On vehicles equipped with a tailgate lifter, the wiring harness securing the rear combination lamp is improperly fastened, causing the wiring to sag. The sagging wiring contacts the exhaust pipe, causing damage …
The driver-side airbag module cover's brand emblem material is inappropriate, causing degradation through hydrolysis. Upon airbag deployment, the emblem may fracture and scatter, potentially injuring occupants.
On refrigerated/freezer vehicle air suspension remote control box mounting brackets, welding of components is not performed at the position specified in the drawings, causing cracks to develop in the bracket. Continued use …
The serial data gateway module software that processes communications from various vehicle system modules is deficient, potentially preventing proper communication processing. Consequently, warning lights may not illuminate when airbag system malfunctions occur, …
The fuel pump impeller (resin-molded rotor) may have undergone improper molding conditions, resulting in low resin density. This causes the impeller to swell and deform when exposed to fuel, potentially contacting the …
The seal at the boot attachment point of the steering gear is inadequate, and the air conditioning drain hose is positioned directly above it. As a result, air conditioning condensation may drip …
In combine harvesters, due to inadequate insulation treatment of the exhaust pipe and its vicinity, as well as improper design, chaff accumulates near the exhaust pipe. During diesel particulate filter (DPF) regeneration …
The driver's seat belt retractor may be improperly manufactured, causing the seat belt to fail to lock during hard braking or similar conditions. As a result, the seat belt may not restrain …
In engines of large trucks and buses, manufacturing variations in the oil pump can cause the pump gear shaft to tilt. This results in gear tooth wear, and continued operation in this …
(1) In the power transmission system, an improper pin selection was made for connecting the primary transmission rod linked to the primary transmission lever with the traveling HST (hydrostatic continuously variable transmission), …
(1) In the power transmission system, the pin connecting the main transmission rod (linked to the main transmission lever) and the HST (hydrostatic continuously variable transmission) was selected inappropriately and connected with …
In leaf suspension variant vehicles, the automatic headlamp leveling control program in the vehicle master control unit is inadequate, causing the headlamp aiming adjustment device to not operate when the lighting switch …
In the braking system of large and medium-duty trucks, the resin piston material in the parking brake relay valve is inappropriate, causing hydrolysis due to moisture in the air circuit. The piston …
In the dashboard, due to improper manufacturing processes, the passenger airbag aperture may not be correctly machined. As a result, the airbag may not fully deploy upon collision, potentially causing excessive injury …
In diesel engines, improper manufacturing control of the timing chain resulted in the use of components without surface treatment. Consequently, the timing chain may stretch during use, causing abnormal noise from the …
In diesel engines, improper manufacturing control of timing chains resulted in the use of components without surface treatment. During use, timing chain elongation causes abnormal engine noise, and in worst-case scenarios, valve …
In the fuel system of engine-powered forklifts, some injector bodies have insufficient strength due to improper process control during molding. Consequently, repeated common rail pressure (fuel pressure) cycles may cause cracks to …
In the damper assembly, the nut securing the rear suspension arm is made of inappropriate material, which in some cases causes premature corrosion cracking. This results in loosening of the arm attachment …
In internal combustion forklifts, the oil seal of the brake master cylinder may have insufficient sealing performance, causing brake boost oil to flow into the brake oil side. Additionally, under frequent brake …
On agricultural tractor brake hoses, improper assembly instructions for adjacent hose clamps result in interference with clamps. Continued operation in this condition may cause hose damage due to running vibration and engine …
Engine mount bracket attachment bolts are susceptible to loosening due to improper installation. Continued operation may result in bolt fracture, causing the engine to tilt and interfere with the front suspension member, …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.