Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 36 of 175
The ESC (Electronic Stability Control) controller contains an error in the braking control program during ACC (Adaptive Cruise Control) operation. When deceleration is required due to approach to a preceding vehicle or …
In combine harvesters, the inadequate design of the DPF muffler high-temperature zone shield cover allows straw to accumulate around the DPF muffler. This can cause the DPF muffler outlet pipe to contact …
In turbocharged engine control computers, the abnormality detection threshold for the intake manifold pressure sensor is set inappropriately. Consequently, during deceleration in low-pressure environments such as high altitudes, false sensor abnormality detection …
The in-tank unit fuel pump has improper clearance design between the resin impeller and cover. Due to elevated fuel temperature, the resin impeller may deform, contact the cover, causing fuel pump motor …
The in-tank unit fuel pump has inadequate clearance design between the resin impeller and cover. Elevated fuel temperature can cause the resin impeller to deform, contact the cover, resulting in fuel pump …
In the damper assembly, the threaded portion of the nuts securing the suspension arms has been improperly machined, resulting in incomplete tightening of the threaded connection. This can cause the fastening bolts …
The passenger seat airbag has an improper folding method, resulting in some units not being properly folded. Consequently, when the airbag deploys during a collision, the seams may tear and prevent normal …
In the Electronic Stability Control (ESC) function, the control program of the hydraulic control unit is inadequate. When the engine is restarted while a handling mode remains selected, the ESC system does …
The fastening structure of the belt-drive pulley in the power transmission device is inadequate, which may cause the pulley fastening nut to loosen during operation. This can result in the pulley contacting …
The low-pressure fuel pump was insufficiently validated against fuel composition. Fuel components contained in Japanese-specification fuel may adhere to and accumulate on the gerotor (metal gear pump) section of the low-pressure fuel …
The control program for the collision mitigation brake in the driving support system is inadequate, preventing correct recognition of guide posts on curved roads and the direction of travel of oncoming vehicles. …
The engine controller's idle intake air volume control program is improper, which may result in insufficient intake air volume while the vehicle is stopped in Drive range. This can cause a decrease …
The rear-end lower panel has an improper shape. Running vibration may cause the main wire harness to contact this panel. This can damage the harness insulation, causing internal wiring short circuits, which …
In the front hub bearing of large truck low-floor 4-axle vehicles, excessive interference fit with the knuckle shaft may damage the bearing during front hub assembly. Consequently, bearing damage during use may …
In the intake air preheating device that assists cold-start operation of the engine, insufficient degassing during water-resistant and rust-preventative coating of the preheater relay may allow gas bubbles to remain on the …
In the steering apparatus of low-floor dual-axle heavy-duty trucks, the clamp bolt/nut fastening torque on the left side of the front-front axle tie rod is inappropriate, resulting in reduced clamp clamping force …
On large trucks, the pre-plating acid pickling process for the fixing clamp fastening bolt on the right-side tie-rod end of the front axle is inadequate, causing some bolts to have reduced strength …
In large trucks, improper assembly of the front-wheel brake chamber in the braking system (2) results in insufficient fastening torque on the plug (closure cap), test nipple, and brake hose connection (nipple …
In large trucks equipped with air suspension and vehicle-height adjustment devices, the shock absorber piston structure is inadequate. Lateral forces cause excessive contact pressure between the piston and cylinder. Repeated cycles of …
In large trucks, the battery hold-down plate has an improper shape, causing the power cable to interfere with the plate edge when attached to the battery terminal. Continued use in this condition …
On tire rollers, if the fuel tank cap is not properly installed after refueling, water may enter the fuel tank through the filler opening. If water accumulation exceeds the water separator capacity …
In the GM (Grand Module), due to improper electrical load design, operating the brake while sounding the horn may trigger a brake light failure warning. The brake light may not illuminate until …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to fuel absorption caused by inadequate molding conditions that result in low resin density. This can cause …
The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to inadequate molding conditions resulting in low resin density, causing expansion when exposed to fuel. This can …
In the dashboard, due to inadequate manufacturing control, the skin is not properly welded to the carrier in some units. As a result, when the passenger-side airbag deploys during a collision or …
In the rear axle U-bolt nut tightening process for small trucks, improper fastening equipment settings result in insufficient tightening torque on some units. Continued operation may cause the nut to loosen and …
In vehicles equipped with the optional emergency brake system, certain display units have improper manufacturing specifications at the LCD panel mounting section, resulting in missing waterproof treatment. Rainwater and other moisture can …
The drawbar support (coupling device) on agricultural tractors has insufficient fastening bolt strength, which can result in fastening bolt failure. This may cause an agricultural work trailer attached to the tractor to …
Excessive grease was applied to the O-ring of the reservoir piston in some ABS (anti-lock brake system) modulators due to inadequate management of the grease application equipment. As a result, grease that …
In large-size transit buses, the engine ECU control program is inadequate, which may cause maximum combustion pressure to exceed the allowable limit of the connecting rod. Continued operation in this condition may …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.