Before you buy, check it isn't under a dangerous recall.

In the fuel pump of rotary snow removal vehicles, improper selection of the permanent magnet inside the pump causes demagnetization in low temperatures, resulting in high-speed and high-current operation of the motor …

In the braking system, due to improper programming of the IEB module, the motor motion detection sensor generates an abnormal signal and illuminates the warning light. When this occurs, the fail-safe does …

The brake light switch contains rubber components molded using an inappropriate mold release agent, resulting in some components containing silicon. This causes silicone gas to accumulate inside the switch. When the switch …

In the braking system, the brake fluid injection process for the rear-wheel brake system (ABS modulator) was performed improperly, resulting in minute air bubbles contained within the brake system fluid in some …

In the DC-DC converter of mild hybrid electric vehicles (MHEV), the control program is inappropriate, causing the transistor to not switch properly when electrical load occurs within the DC-DC converter. As a …

The driver-side airbag inflator may accumulate moisture when exposed to high-temperature, high-humidity environments over prolonged periods. During airbag deployment, internal pressure in the inflator may rise abnormally, causing the inflator container to …

The rear glass of the rear hood on certain vehicles is not properly bonded to the rear hood due to inadequate cleaning of the glass adhesion surface. Consequently, the adhesive bond may …

Due to inadequate manufacturing equipment control, some fuel pumps have developed protrusions on their inner diameter, obstructing fuel transfer between tanks. When the primary tank fuel level drops, fuel may not be …

Improper foreign material control during fuel tank manufacturing allows oxides generated inside the tank during welding to adhere to the fuel pump suction filter. This can clog the filter, causing engine malfunction, …

In the fuel systems of engine-powered forklifts and wheel loaders, certain injectors have insufficient strength due to inadequate process control during injector body molding. Repeated common rail pressure cycles may cause cracks …

In the parking support brake system, the rear camera control program is inappropriate, which may prevent detection of pedestrians during reverse. As a result, the collision mitigation brake may not operate properly.

①In the input damper of the hybrid transaxle, improper application of rust-preventive oil may cause the oil to adhere to the damper's power transmission section. As a result, abnormal slipping of the …

On light-duty trucks, some front-wheel brake calipers have slide pins without grease applied. Continued operation in this condition can cause the outer pad to fail to retract fully after brake actuation, resulting …

Some units have insufficient tensioner strength due to inadequate manufacturing control of the camshaft chain tension adjuster in the engine. Consequently, the tensioner may fail prematurely, preventing proper tension maintenance, causing abnormal …

The Smart Brake Support (SBS) control program in the vehicle control computer is inappropriate, which may prevent proper recognition of vehicles stopped on the roadside of S-curves or large road signs. As …

Due to improper cutter settings during electric power steering harness assembly, some wiring insulation is damaged. Moisture ingress during vehicle use can cause electrical failure, resulting in loss of electric power steering …

Dual-clutch transmissions have improper oil quantity due to incorrect lubrication device settings during manufacturing. Some vehicles have excessive or insufficient transmission oil. Excessive oil may leak from the bleeder; insufficient oil causes …

The fuel injection control program in the engine control computer is inadequate. When large amounts of fuel evaporative gas flow into the combustion chamber, the injector may fail to properly control fuel …

Due to improper storage management of the fuel pump and fuel filter, biodiesel fuel injected at the vehicle factory may degrade during extended vehicle storage. This can cause clogging of the fuel …

The rubber seal in the engine compartment has insufficient heat resistance. When the turbocharger repeatedly reaches high temperatures, the rubber seal may harden due to heat. This can cause the seal to …

In left and right front-seat side airbags, inadequate process control during vehicle manufacturing has resulted in some units where the airbag mounting nuts are not tightened to the specified torque. Consequently, the …

In shovel-loader brakes, air bleeding operations in the brake circuit during manufacturing may be inadequate. Consequently, during high-speed, long-distance operation with minimal brake application, residual air in the brake circuit expands as …

The cowl cover installed on top of the brake master cylinder reservoir has inadequate drainage design, allowing rainwater to enter the brake fluid. Rainwater reacting with the brake fluid causes gelation, which …

In the brake booster, some resin pistons have reduced strength due to improper molding conditions. Repeated brake pedal operation may cause piston fracture, which in the worst case could impair the boosting …

During reassembly of the propeller shaft following removal for concrete pump apparatus installation, inadequate work management has resulted in reuse of removed fastening bolts. This causes insufficient fastening torque, allowing bolts to …

In the rear wheel brake calipers, assembly variation of the parking brake actuation shaft may cause the corrosion-preventive coating to peel off. If water infiltrates the shaft through the seal, rust develops …

The steering joint connecting the intermediate shaft and steering gearbox in the steering mechanism may not be installed in the correct position due to improper assembly work instructions. If the vehicle continues …

The crankcase internal pressure design during deceleration is inadequate, causing cylinder pressure to drop below crankcase pressure during deceleration. This allows blow-by gas containing engine oil to flow backward into the combustion …

In high-voltage batteries, foreign matter may be present inside the cell module due to improper manufacturing processes. This can cause battery circuit short circuits, resulting in abnormal current discharge. In the worst …

In the front wheel braking system (master cylinder), improper work management during component assembly has resulted in units being assembled with missing internal parts. Consequently, brake fluid pressure may not develop, risking …