Before you buy, check it isn't under a dangerous recall.

In the prefuse box that manages vehicle power supply, the nut-fastening device programming is inadequate, resulting in some units where the fixed nut securing the live metal plate is not assembled. Consequently, …

The defoaming mechanism of the sealing cap in the hydraulic stabilizer control unit's oil reservoir is inadequate. During sustained driving with significant attitude changes, oil may spray out from the vent hole. …

The control unit of the electric parking brake may have insufficient strength in circuit board elements due to improper board handling during component manufacturing, or sensor components may have insufficient strength due …

The brake hydraulic unit ECU has an improper control program. Electrical noise may occur during pump motor control switching in the hydraulic unit, potentially interrupting ECU control. This may cause ASC (Vehicle …

In the auxiliary brake light, improper positioning of the printed circuit board wiring in the internal substrate may cause interference with the fixing screw during vehicle vibration. This results in damage to …

The ignition switch position-retention spring may have been damaged during molding due to inadequate maintenance of the molding equipment. Repeated ignition key operation can cause this spring to fracture. If heavy objects …

Due to improper device registration of the radar sensor control computer, the pedestrian detection automatic braking system is manufactured in a non-functional state. Therefore, when the radar sensor detects a pedestrian, the …

The hybrid system computer has inadequate control software. During high-speed driving, when the accelerator pedal is depressed substantially, the computer may fail to complete gear shifting processing within the specified time. Consequently, …

In engine compartment electrical wiring, assembly variation was not adequately evaluated, causing interference between the wiring and surrounding components in areas without protective covers. Vibration during operation may damage the wire insulation, …

Improper welding between the pin securing the center stand spring and the left center stand bracket can cause the pin to fracture and the spring to detach. This may prevent the center …

The exhaust gas cooler in the diesel engine exhaust gas recirculation (EGR) module has insufficient durability, causing coolant leakage. Soot in the exhaust gas mixes with the coolant and accumulates inside the …

The left and right door latches have insufficient strength in the spring hook attachment area within the latch. Repeated door opening and closing can cause this component to fracture. As a result, …

Agricultural tractor brake switches have insufficient water resistance, allowing water ingress into the switch interior and causing electrical continuity failures. This may result in brake lights failing to illuminate or remaining continuously …

In the starter switch harness of combine harvesters, improper routing of the harness may cause contact between the harness and links within the steering column during steering operation. Continued use may result …

The plastic drain hoses for the air cleaner box and fuel tank cap are routed improperly, causing contact with the exhaust pipe in some cases. This can result in melting of the …

Certain brake fluid with improper composition is prone to absorbing moisture from the atmosphere due to aging. The brake fluid may gel, clogging the ABS unit's pressure valve. If the pressure valve …

The relay controlling the engine starter has improper molding, causing internal contact deformation in some units. When relay contacts remain continuously engaged, the starter continues rotating; in worst cases, the starter overheats …

The water drain hole position in the rear suspension lower control arm is inadequate, causing rainwater that has entered the lower control arm to not drain properly. This can result in corrosion …

In the fuel pump of rotary snow removal vehicles, the motor brush structure is inappropriate, causing abnormal brush wear and poor contact. This may result in fuel pump malfunction, and in the …

In light trucks, improper routing of the driver-side airbag ECU wiring harness may cause the wiring to be pinched and severed between the front panel and the ECU mounting bracket during front …

In light-duty trucks and buses, improper maintenance settings for the centrifugal separator filter in the blow-by gas recirculation device can lead to filter clogging. If frequent extended idling or inadequate engine oil …

In the reducer manufacturing process, the parking lock actuation verification inspection method (which mechanically locks the wheels when the shift lever is in P range) was inadequate, resulting in some parking pole …

The piston in the front brake master cylinder has insufficient strength due to inappropriate material selection. Cracks may develop in the piston due to brake fluid pressure during brake operation. If use …

For occupants in the rear center seat and rear left seat, the mounting position of the rear center seat belt buckle is inappropriate. When large lateral forces are applied to the rear …

On large-wing vehicles equipped with side skirts, the striker that secures the side skirt at the rear overhang lacks sufficient strength. Cracks may develop due to running vibration and other factors. Continued …

The front wheel support section of the motor sweeper frame has insufficient strength, which may cause cracks due to vibration during operation. If use continues in this condition, the support section may …

The waterproof cover of the brake booster is not properly installed according to the service manual in some vehicles. This allows rainwater to contact the device, causing corrosion and loss of vacuum …

Interior door handles have insufficient strength in the return spring retainer. When the interior door handle is operated, the retainer may break, causing the return spring to disengage and the handle to …

In the steering device of the shovel loader, the steering hydraulic hose lacks sufficient strength. When hydraulic pressure is applied to the hose during steering, the hose may separate, causing hydraulic fluid …

In the shovel loader fuel pump, improper motor brush structure causes abnormal brush wear and contact failure. This results in fuel pump malfunction, and in the worst case, the engine may stall …