Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 75 of 173
In large truck and bus engines, manufacturing variation in the oil pump can cause the pump gear shaft to tilt. This causes gear tooth wear, and continued operation leads to gear breakage, …
On steering wheels with genuine leather trim, when the operator releases their hand after turning the steering wheel and slides it to return to the straight-ahead position, the hand may contact the …
In light-duty trucks equipped with driver and passenger airbags, certain vehicles have not undergone airbag control unit specification verification due to inappropriate manufacturing process and vehicle inspection item data instructions. Consequently, if …
The side stand has improper welding at the moving parts and cannot withstand the vehicle weight during parking, causing the welded section to break in some cases. This may result in the …
The stud bolt that secures the battery cable terminal to the engine compartment bulkhead has an improperly torqued nut. Vibration during operation can cause the nut to loosen, resulting in poor contact …
The parking control lever, which actuates the automatic transmission parking mechanism (a mechanism that mechanically locks the transmission output shaft), has insufficient welding process control. When the shift lever is moved to …
During engine side mount installation work, the insulation of electrical wiring (engine room wire harness) has been damaged by tightening bolts. As a result, if the wire insulation breaks due to vibration …
In the forward collision mitigation system (collision mitigation brake system), improper management of repair parts for the adaptive cruise control unit has resulted in some vehicles being assembled with obsolete parts. Consequently, …
The inflator (inflation device) of the front passenger single-stage deployment control airbag may rupture and scatter upon airbag deployment, potentially causing fire or passenger injury.
In medium-duty dump truck and mixer specifications, the front underride protection device bracket has an improper shape. When the steering wheel is turned right, the pitman arm and drag link boot may …
In hybrid vehicle fuel pumps, improper pump motor speed settings cause motor brush vibration, leading to premature wear. This activates warning lights, prevents fuel supply, disables engine operation, and may result in …
In the engine fuel line (delivery pipe), the fastening tool for the fuel pressure sensor is inappropriate, causing interference with adjacent components during fastening and resulting in insufficient fastening force. This may …
The vent hose that regulates pressure within the fuel tank has an inadequate design. When engine heat increases fuel tank pressure, fuel may leak from the vent hose. Leaking fuel can flow …
In the engine, some units have improper cylinder head gasket manufacturing, resulting in insufficient sealing surface pressure at the interface between the cylinder and cylinder head. Consequently, engine oil flows into the …
The fuel hose on the low-pressure side of the engine has insufficient strength due to improper hose material. Additionally, some vehicles have improper hose clamps installed relative to the hose outer diameter. …
Battery cable fastening is inadequate. Additionally, some starter motor terminal insulation covers are not properly installed. Conductive heat-resistant shielding wrapped around the battery cable may contact the starter motor terminal due to …
In large-capacity transit buses equipped with automatic transmissions, the torque converter backing plate mounting bolts to the torque converter cover are fastened improperly, and the torque converter cover threaded portion is machined …
The inflator container may rupture and scatter during airbag deployment, causing fire or occupant injury.
The bolts fastening the front suspension lower arm may have insufficient strength, causing bolt fracture and abnormal noise in some vehicles. Continued use in this condition risks lower arm detachment, resulting in …
In vehicles equipped with vertical-type tail lifts, inadequate process control during manufacturing has resulted in insufficient tightening of the lock handle mounting nuts on the tail lift. Continued use in this condition …
Due to improper assembly of the brake booster lip seal, some units were assembled without grease application. This increases sliding resistance of the lip seal, which can cause rollback and air leakage. …
The control program in the engine control unit immediately before vehicle stop is inappropriate, and there is a risk of engine stall immediately before vehicle stop in situations of high engine load, …
The oil filter housing in the oil filter module is made of inappropriate material, causing thermal expansion due to engine temperature. Repeated thermal expansion deforms the housing, compromising the seal integrity and …
Due to improper manufacturing processes within the fuel pump, plating coating on internal components may peel off and remain as foreign matter inside the pump. Continued use in this condition may cause …
In the fuel pump, improper manufacturing processes inside the pump cause plating coating on internal components to peel off and remain as foreign matter inside. Continued use in this condition may allow …
The power window switch in the driver's door has insufficient lubricating grease due to improper application method. Wear particles and moisture ingress from the terminal sliding contact form a short circuit, causing …
The vehicle body lacks sufficient structural strength at the hood latch mounting area. During high-speed driving with the hood primary lock disengaged, wind pressure and similar forces may cause deformation of the …
The driver-side airbag inflator may rupture during deployment, causing internal components to scatter and potentially injuring occupants.
Excessive grease was applied to the contact points inside the ignition switch. During switch operation, arc discharge heat causes the grease to carbonize and accumulate between the movable and fixed contacts, reducing …
The sealing ring material in the engine timing chain tensioner is inadequate, which may cause engine oil leakage. Continued operation in this condition may result in warning light illumination and engine damage. …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.