Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 96 of 175
Certain airbag control units have insufficient electrical noise immunity. Noise generated by vehicle electrical components can damage the IC chip within the unit during use, and in the worst case, may cause …
The fuel pump has insufficient internal bearing durability, which may cause bearing wear, resulting in impaired operation and abnormal noise. Continued operation in this condition may lead to progressive wear, reducing fuel …
Some brake actuators have incorrect seal rings installed. This allows brake fluid to leak into the brake actuator from the seal area, causing the warning light to illuminate. Continued operation may result …
In the brake vacuum electric pump that supplies negative pressure to the brake booster, some units have cracks that occurred during machining because internal vane inspection was inadequate. Continued use of such …
The brake vacuum electric pump that supplies negative pressure to the brake booster has an improperly machined internal rotor in some units, resulting in a sharp pointed tip. Continued use may cause …
In diesel engines, improper setting of maximum engine RPM causes excessive load on the crankshaft No. 3 main journal at maximum engine speed, resulting in journal bearing misalignment that can obstruct oil …
Some mounting nuts on the stud bolts that secure the steering gearbox have insufficient tightening. When steering is operated, abnormal noise may occur. If use continues in this condition, in the worst …
Certain rear brake caliper mounting bracket fastening bolts are insufficiently torqued. This may cause noise from the vehicle rear during operation or braking. If the noise is ignored and driving continues, the …
Brake vacuum pipes have insufficient strength due to improper manufacturing processes, and cracks may develop in the brake vacuum pipe. Consequently, the negative pressure in the brake booster may be insufficient, causing …
The swashplate, a subcomponent that regulates hydraulic fluid discharge in the steering hydraulic pump, may have reduced surface hardness due to improper heat treatment. Continued operation in this condition causes excessive wear …
Improper stitching in the right-side window airbag may cause seam separation upon deployment following collision detection, resulting in internal pressure loss, premature deflation, and potential failure to provide adequate protection.
The mounting bolts of the engine hood secondary lock striker may have been tightened with improper torque during manufacturing, causing the striker to detach and the secondary lock to malfunction. As a …
The connector portion branching the electrical circuit from the main harness is covered with tape. During rain or wet driving conditions, water entering from the main harness end may travel through the …
Certain serration rails, an interior component, have improper spot welds with the airbag cover panel. When the passenger-side airbag system deploys upon collision detection, the serration rail may separate from the airbag …
In the signal pressure piping for controlling the braking device of the rear axle, attached to the relay emergency valve of the full trailer, improper routing of the piping may cause cracks …
The terminals in the electrical wiring connection connector of the combination lamp (backup light, tail light, brake light, and turn signal indicator) bulb holder may be deformed. As a result, insulating material …
On trailer air brake hoses, improper crimping of the fittings to the rubber hose can cause the internal hose insert fitting to damage the hose, resulting in air leakage. Continued operation in …
On trailer axles, the wire attachment position of the catch strap device that limits air suspension extension height is improperly positioned, causing wire-to-axle interference in some units. Continued use in this condition …
On vehicles equipped with gasoline engines, improper routing of battery cables may cause interference between the cable and the engine's hot water connector. Continued use in this condition risks cable damage from …
During prolonged continuous operation near maximum engine RPM, vehicle vibration may cause air bubbles to form in the brake fluid within the front brake oil reservoir tank. If operation continues in this …
Improper fastening method of the mounting bolts for the bracket holding the license plate and safety lights. Vibration during operation may cause the mounting bolts to loosen and detach, resulting in these …
In the engine, there is variation in wrinkles inside the connector portion generated during fuel pipe manufacturing, and some pipe connector portions have low fastening torque. As a result, when high fuel …
In the engine, variations exist in wrinkles inside the connector portion during fuel pipe manufacturing, and some pipe connectors have insufficient tightening torque. When high fuel pressure is applied, cracks may initiate …
In the engine, variations exist in wrinkle formation inside connector portions during fuel pipe manufacturing, and some pipe connector portions have insufficient fastening torque. Consequently, high fuel pressure can initiate cracks at …
Engines installed in medium and small trucks and small buses may have inconsistent wrinkles in the connector interior during fuel pipe manufacturing, and some pipe connectors have insufficient tightening torque. When high …
The gearbox-side strength of the intermediate extension shaft coupling component connecting the steering wheel and gearbox is insufficient in some vehicles. Repeated forceful full-lock steering operations at low speeds may cause play …
The door opening/closing control program is inappropriate. Additionally, there is manufacturing variation in the sensor that detects the door position just before closing, which is installed to activate the closer mechanism that …
The door open/close control program for the boarding/alighting door is inappropriate. When the driver performs certain operations during the process from running to stopping (shifting to N and opening the boarding/alighting door …
(1) Due to improper fuel cooler structure, air can become trapped inside the device. When the vehicle vibrates, the fuel piping may draw in this trapped air, causing unstable fuel supply to …
(1) Improper fuel cooler structure allows air to accumulate internally. When the vehicle vibrates, fuel lines may draw in this trapped air, causing unstable fuel supply to the engine, resulting in engine …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.