Before you buy, check it isn't under a dangerous recall.

The rear shock adjuster mounting bracket has insufficient structural design. Vehicle vibration at high engine RPM causes the bracket to resonate and develop cracks. As cracks propagate and fracture, the rear shock …

The front, rear, and side glass (excluding door sections) of the wheel loaders were installed using incorrect primer, resulting in weak adhesive bonding. Over time, adhesive strength degrades, causing separation and allowing …

Takata airbag inflator may rupture, ejecting metal fragments

The body control module has a software deficiency due to insufficient design review. As a result, when tire pressure decreases by 20% or more, the tire pressure warning lamp does not illuminate …

The headlamp control module has inadequate design review, resulting in program deficiencies. Consequently, even when approaching motorcycles or bicycles are detected, the driving headlamps do not dim and fail to comply with …

The rear seat outer headrests (left and right) may have improper dowel pin assembly between the headrest bar and headrest box due to inadequate manufacturing process control. In the event of vehicle …

The starter motor may fail to engage due to incorrect detection of engine start conditions, causing the auxiliary restart motor to be used continuously. This places excessive load on the accessory belt …

①The bearing durability of the automatic tensioner that maintains constant accessory belt tension is inadequate, and the belt lacks sufficient wear resistance and durability against temperature changes. Consequently, fracture may occur due …

During repair, when replacing the front chassis input/output module from the old type to the current type, improper programming instructions result in the headlight auto-on function software not being updated to the …

In the electronic air dryer, when replacing the legacy Central Chassis Input/Output Module with the current model during repair, improper firmware programming instructions result in the air dryer regeneration software not being …

In the electronic air dryer, when replacing an older Central Chassis Input/Output Module with the current model during repair, improper programming instructions result in the air dryer regeneration software not being updated …

In high-pressure fuel pumps, improper manufacturing processes have resulted in some units where the fixing bolts are not tightened to the correct torque. Consequently, during use, the pump fixing may loosen, causing …

In the powertrain, the control program of the integrated drive force control unit is inappropriate, causing electrical noise generated from the unit's power supply IC to be incorrectly diagnosed as a malfunction. …

In the adaptive-distribution headlight beam-aiming adjustment device, due to improper vehicle calibration settings, the optical axis does not adjust correctly when loaded, causing downward deviation and potential non-compliance with safety standards.

Certain supply pumps in replacement repair parts have insufficient component strength due to inadequate surface treatment in the manufacturing process. Repeated high-load operation may cause cracks to develop, potentially resulting in fuel …

The starter's waterproofing design is inadequate. Water can penetrate inside the starter relay when driving through puddles at high speed. Continued use may cause contact point short-circuiting, resulting in engine failure to …

The starter has insufficient water-resistant design. When driving through puddles or standing water at speed, water may enter inside the starter relay. Continued operation could cause contact points to short circuit, resulting …

The NOx control system via torque reduction in the engine control unit may not operate properly due to insufficient design review. As a result, NOx emissions may exceed the standard limit and …

The power cable of the fuse box has improper manufacturing instructions, resulting in insufficient clearance between the cable and the passenger-side footrest panel in some vehicles. During use, the power cable may …

In the steering valve of the shovel loader, due to improper manufacturing process, the spool bore that distributes hydraulic flow is distorted in some units. As a result, when steering operation is …

The brake system backplate has insufficient design review, and in some cases interferes with the load-handling device lift cylinder. This interference causes friction and wear between the backplate and lift cylinder during …

Due to inadequate headlight inspection at the manufacturing plant's final inspection, the light axis may not comply with safety standards.

In the high-voltage battery power supply for the electric motor, improper management of manufacturing fixtures for battery cells has resulted in foreign material contamination inside some cells. When foreign material penetrates through …

Moisture may ingress into the fuel pressure sensor connector due to high-pressure washing of the engine compartment or similar conditions. This can cause the fuel pressure sensor to malfunction, resulting in increased …

The internal circuit board of the LED approach lamp in the left side mirror has insufficient design considerations. During use, gaps and cracks develop in the potting material (insulation), allowing water and …

The steering controller holder supplied with agricultural tractor steering controllers has insufficient design against water ingress, allowing water to enter the holder interior and causing rust on the spline connecting the internal …

In right-hand drive specification vehicles, the airbag control unit software contains an improperly configured door pressure sensor identification program intended for left-hand drive specification due to inadequate manufacturing processes. Consequently, side airbag …

The control unit of the electric brake booster has insufficient control program review. When Travel Assist is active and the steering wheel is released for a certain period, the system may misidentify …

In the panoramic view monitor, due to insufficient review of the control program, if the vehicle is put in reverse or similar operations are performed immediately after startup, the video of the …

The suspension-type fire extinguisher box bracket may develop cracks due to insufficient design review, which can occur from running vibrations and similar conditions. If use continues in this state, cracks may propagate …