Before you buy, check it isn't under a dangerous recall.

Chemical — The brake shoe contains asbestos fibres. Asbestos causes cancer. The product does not comply with the REACH Regulation.

In the buffer device of wheel cranes, the fastening bolts of the upper torque rod and lateral rod are not tightened to the specified torque due to improper fastening. Continued operation in …

In the power transmission system of combine harvesters, inadequate design review has resulted in insufficient weld penetration around the tension arm pivot shaft. Vibration and impact during machine operation concentrate stress at …

The headlight unit has insufficient design review. Internal components may degrade faster than normal due to heat generated by the LED structure itself. Continuous use can cause thermal damage to internal components, …

In the SSAM (Single Signal detect and Actuation Module), insufficient software review can cause the microcontroller within the SSAM to repeatedly reset when the SSAM activates or during operation, as it may …

In the detection method and control program for each operation of single-unit vehicle transport vehicles, insufficient design verification and evaluation may result in detection defects and control program errors, causing operation to …

In the vehicle-mounted equipment control unit of single-deck car-carrier vehicles, the control program design is inadequate, which may result in partial loss of the program. Continued operation in this condition may prevent …

The base plates for mounting the door lock strikers on both left and right doors may have insufficient welds to the door frame. Due to door opening/closing operations and vibrations during driving, …

The unit controlling traffic situation information has insufficient program design review, which may result in delayed detection of obstacles ahead. Therefore, the vehicles do not comply with UN Regulation No. 159.

On vehicles equipped with the omnidirectional safety driving support system, the control program of the driver monitor camera control computer is inappropriate, causing computation processing to potentially not terminate after external diagnostic …

In electrical wiring, spatter removal instructions during frame welding were inadequate, resulting in spatter remaining in the main harness routing areas. When the harness interferes with spatter and continues to be used, …

The front door control unit has an inappropriate control program, which may cause the following malfunctions: • Door glass pinch detection function does not operate • Central door lock does not function …

Due to inadequate manufacturing control, some fuel tanks have localized indentations on the filler neck sealing surface. Consequently, the rubber gasket on the fuel tank cap cannot conform to these localized indentations …

The detachable portable battery mounted on electric two-wheelers has improper welding conditions for cell components inside the battery, which may cause electrolyte leakage from damaged cells. If use continues as-is, metal dendrites …

Due to insufficient consideration of the surface treatment method for seat interior materials, flame spread occurs at a faster rate than specified in the combustion test standard, failing to comply with safety …

In the combination meter, insufficient control program review causes circuit board components to degrade prematurely as operating hours accumulate. This may result in the meter display failing to appear during engine startup, …

The controller design in electric forklifts is insufficient. Under repeated high-load operation over extended periods, the metal controller terminal block reaches high temperatures and exhibits creep behavior. This causes the fastening torque …

In the bush component of the engine fan for radiator cooling on engine-type forklifts, there are units with insufficient crimping due to inadequate equipment condition settings established for each production lot. As …

In the high-voltage battery cell modules, due to improper manufacturing, the edge of the positive electrode sheet is slightly misaligned, which may cause separator damage. This can result in micro short-circuits within …

The crop divider (a device that separates crops during harvesting and threshing operations) on the harvester-thresher has improper manufacturing methods, causing some dimensions to exceed design specifications. When assembled into this machine, …

In the braking system, the brake valve and connector are offset left and right on the mounting position, and the rear wheel brake air piping (nylon tube) has an improper shape. Cab …

In the flywheel housing, improper fastening instructions during manufacturing have resulted in some plate cover attachment bolts not being tightened to the specified torque. Continued use in this condition may cause bolt …

Due to insufficient consideration in the camshaft fixing method, the bolt clamping force securing the camshaft fixing plate is inadequate in some units. Continued operation in this condition may cause the bolts …

In N mode, due to insufficient design review, when brake pedal and accelerator pedal signals are input simultaneously to the VCU while driving with ESC disabled, the vehicle may misjudge a slip …

The Brake Control Module (BCM) has improper programming. When coasting downhill in B mode or one-pedal drive mode, the BCM may fail to properly regulate brake fluid pressure during braking. As a …

Rear fuse box panel fixing screws have improper manufacturing processes, resulting in screws of varying lengths being used, some of which contact electrical wiring. Continued use may cause electrical wiring damage from …

The Engine Control Module (ECM) has insufficient design consideration, which may cause unstable idling at extremely low speeds. As a result, the engine may unintentionally stall during acceleration or at extremely low …

The crankshaft in certain engines has manufacturing defects: uneven surface treatment on the connecting rod journal mounting surface and dimensional errors in the journal. This can cause the connecting rod and crankshaft …

The bolts fastening the upper and lower crankcase of the engine were tightened with excessive torque due to improper tightening procedures. This prevents proper oil clearance between the crankshaft bearing and crankshaft, …

In the cooling system of agricultural tractors, the cooling water drain hose assembly is improperly installed with insufficient fastening force. Continued operation in this condition may cause the cooling water drain hose …