Before you buy, check it isn't under a dangerous recall.

The waterproof film located inside the upholstery of the seat cushion and backrest, as well as portions of the urethane material, were selected inappropriately, causing combustion at a faster rate than the …

The headlight unit design review was insufficient. Internal components degrade faster than normal due to heat generated by the LED structure itself. Continuous use can cause thermal damage to internal components, resulting …

The filter mesh inside the inflator of the front passenger airbag may have excessively dense weave due to improper manufacturing process. This can cause pressure to rise within the inflator during airbag …

In the driver's seat belt, improper installation during vehicle manufacturing results in some end fittings not being properly secured to the bolt. Consequently, the seat belt may detach due to vibration during …

In the 12V and 48V ground wiring beneath the vehicle, improper assembly during manufacturing has resulted in some units where the nut at the body ground terminal point is not tightened to …

In the panoramic sunroof, due to improper manufacturing instructions, cushioning material is not attached to the connecting strut. As a result, the vehicle does not comply with standards regarding interior protrusions in …

The Drivetrain (CPC) Control Unit and Engine Control Unit had improper control program distribution management, resulting in incorrect control programs being written. Consequently, the vehicles do not comply with safety standards regarding …

The Electronic Stability Program (ESP) control unit has an inadequate control program due to insufficient design review. When the ESP malfunctions, this causes non-standard warning messages to be displayed, failing to comply …

On the left and right front fenders, insufficient design consideration has resulted in wheels protruding from the fenders on some vehicles. This may result in non-compliance with safety standards.

Non-compliant stickers other than those specified are affixed to the front windshield due to insufficient regulatory confirmation, failing to meet the safety standards for road motor vehicles.

Due to improper manufacturing process of front tires, the carcass inside some tires is not formed at the correct angle. Consequently, during high-speed or high-load driving, stress concentrates on the carcass causing …

In inline 2-cylinder engines, the engine control computer's fuel injection control program and fail-safe control program during misfire detection are inappropriate. When driving with low throttle opening from high to low altitude, …

During vehicle manufacturing, software information could not be verified due to inadequate re-inspection equipment after repairs.

Rear-view mirrors have improper design dimensions: 1. Some left-side rear-view mirrors have a smaller mirror radius of curvature. 2. Some interior rear-view mirrors (convex type) have narrower mirror width. As a result, …

In rear-view mirrors, design dimensions are inappropriate: 1. Some left-side rear-view mirrors have an excessively small mirror surface radius of curvature. 2. Some interior rear-view mirrors (convex type) have an excessively small …

Interior rear-view mirrors (convex type) may have insufficient mirror width due to inadequate dimensional control during manufacturing. This may result in non-compliance with one-man bus structural requirements.

Interior convex mirrors lack adequate design review, resulting in some units with effective dimensions below 300 mm. This may violate structural requirements for single-operator buses.

The electric air compressor that supplies air to the brake air tank has insufficient heat-resistance evaluation of its internal bearings. The bearings may seize, causing a reduction in compressor rotational speed and …

Rear-view mirrors have improper design dimensions: (1) Some left-side rear-view mirrors have a small mirror surface radius of curvature. (2) Some interior rear-view mirrors (convex mirrors) have a narrow mirror surface width. …

The rear-view mirrors have inappropriate design dimensions: (1) Some left-side rear-view mirrors have an excessively small mirror surface radius of curvature. (2) Some interior rear-view mirrors (convex mirrors) have an excessively small …

Interior rearview mirrors (convex type) may have insufficient mirror width due to inadequate dimensional control during manufacturing. This may result in non-compliance with one-man bus structural requirements.

In rear-view mirrors, due to inappropriate design dimensions: (1) some left-side rear-view mirrors have a small mirror surface radius of curvature; (2) some interior rear-view mirrors of certain specifications have a small …

In rear-view mirrors, due to inappropriate design dimensions, (1) some left-side rear-view mirrors have a small radius of curvature. (2) some interior rear-view mirrors of certain specifications have a small mirror surface …

Due to improper control software in the BMS (Battery Management System) and DCB (DC Box), a CAN communication error may be incorrectly detected. This may cause the EV system warning light (red) …

In the Electric Parking Brake (EPB), manufacturing defects in internal components may cause the system to detect overcurrent during engagement/disengagement operations, resulting in brake system shutdown. This can lead to insufficient braking …

The travel hydraulic pumps on tire rollers and graders have inadequate design drawings, resulting in insufficient strength of pump component parts (parallel keys). Consequently, the parallel key may fracture during operation, preventing …

In the driver's seat, insufficient design consideration of the seat suspension can cause the suspension to remain locked and fail to release when the seat height adjustment is operated with the battery …

The electric parking brake warning lamp display and software contain design defects. The warning lamp identification is absent and the lamp illumination conditions are defective. As a result, both red and yellow …

In the prime mover of agricultural tractors, improper manufacturing of the tensioner pulley, which maintains tension in the drive belt for the cooling system and related components, can cause cracks in the …

In the brake booster, the diaphragm manufacturing process was inadequate, resulting in some diaphragms exceeding the specified thickness. Consequently, cracks may develop in the diaphragm's curved section. If operation continues in this …