The inflator in the passenger-side airbag may degrade under prolonged exposure to high temperature and humidity cycles. Upon airbag deployment, the inflator container could rupture, potentially injuring occupants.
Ferrari 458Italia 2014–2018
Ferrari 458Speciale 2014–2018
Ferrari 458Speciale A 2014–2018
Ferrari 488GTB 2014–2018
Ferrari F12tdf 2014–2018
+6 more
In the fuel tank cover of the combine harvester, some units have been assembled with incorrect orientation, causing contact with the fuel hose. Continued operation in this condition may result in cracks …
Yanmar YH6115 2018
The lower guard on agricultural tractors has an improper mounting structure. Repeated vertical loads on the front wheels cause loosening of the mounting bolts. Continued operation in this condition may result in …
Yanmar YT330 2016–2019
Yanmar YT333 2016–2019
Yanmar YT338 2016–2019
Yanmar YT345 2016–2019
Yanmar YT352 2016–2019
+1 more
The mounting panel of the driver's seat assist grip lacks sufficient strength. Repeated use can cause cracking in the panel. If used in this condition, the assist grip may detach when the …
Isuzu Journey 1999–2013
Nissan Civilian 1999–2013
The timing belt of the engine may have insufficient tooth strength due to improper manufacturing process. Continued use may result in belt tooth damage, causing warning lights and indicators to illuminate. In …
Honda Legend 2018
Hoses with fittings used in fuel tanks and hydraulic oil tanks may have damaged internal wire due to incorrect equipment being used during the hose insertion process into the fitting. As a …
Komatsu WA100-8 2018–2019
Komatsu WA200-8 2018–2019
Komatsu WA270-8 2018–2019
Komatsu WA320-8 2018–2019
Komatsu WA380-8 2018–2019
In the front suspension, some vehicles have coil springs with improper geometry, resulting in unstable contact with the spring seat. During large vehicle bouncing, the spring may shift and interfere with the …
Nissan Note 2012–2019
In spiral cables attached to the steering wheel of taxi-specification vehicles, the internal structure retaining the wiring is inadequate, causing the wiring to interfere with surrounding components at large steering angles. Repeated …
Nissan NV200 2010–2016
Nissan NV200 Vanette 2010–2016
In ambulances, the surface treatment of the back door lock component is inadequate. Repeated opening and closing of the back door causes premature wear of the component, resulting in illumination of the …
Toyota Toyota Ambulance 2012–2018
In the front damper assembly, the damper shaft material and geometry are inadequate, resulting in insufficient durability of the damper shaft in some units. Consequently, repeated steering inputs may cause damper shaft …
Honda S660 2016–2017
Inadequate water sealing at the joint between the cowl louver and dash panel allows rainwater to drip onto the brake booster. This can cause rust to develop on the brake booster. If …
Daihatsu Wake 2010–2018
Daihatsu Tanto 2010–2018
Daihatsu Hijet 2010–2018
Daihatsu Move 2010–2018
Subaru Stella 2010–2018
+1 more
In the automatic clearance adjustment mechanism (strut set) between the rear wheel brake shoes and drum, improper grease application during component assembly has resulted in some adjuster bolts lacking grease on their …
Daihatsu Wake 2016–2017
Daihatsu Cast 2016–2017
Daihatsu Tanto 2016–2017
Daihatsu Thor 2016–2017
Daihatsu Hijet Caddy 2016–2017
+14 more
The combination meter has improper circuit configuration. When the vehicle interior is exposed to moisture for extended periods, condensation may form on the meter substrate, causing the power circuit section to short. …
Subaru Legacy 1998–2001
The instrument cluster program controlling the brake pad wear warning is inappropriate, so the warning light does not illuminate when brake pads are worn beyond the limit. Consequently, brake pads may be …
Porsche Cayenne 2016–2018
Porsche Cayenne S 2016–2018
Porsche Cayenne Turbo 2016–2018
Porsche Panamera 2016–2018
Porsche Panamera 4 2016–2018
+4 more
Due to improper programming in the electric power steering control unit, the power steering assist function may stop during driving. This may result in increased steering effort.
Bentley Continental GT 2018
The body panel to which the rear center seat belt and buckle are attached has insufficient strength. In the event of vehicle collision with occupants seated in either or both of the …
Bentley Mulsanne 2012–2018
In diesel engine fuel supply systems, the hose clamp attached to the fuel supply hose feeding the high-pressure fuel pump may develop rust due to inadequate corrosion protection. This can cause the …
BMW BMW 320d 2012–2014
In the blow-by gas recirculation device of the asphalt finisher, the air inlet hose material is inappropriate, causing accelerated deterioration and potential cracking of the hose. This may result in air leakage …
H A N T A F60W5 2017–2018
住友 HA60W-10 2017–2018
In the braking system of large trucks with dual rear-axle drive, due to improper work instructions, the air pressure test connector for the braking system was incorrectly installed in some units. As …
Mitsubishi Fuso Super Great 2017–2018
On the flip-type ramp board installed at the bus mid-door entrance, the handle component dimensions are inadequate, causing the handle to protrude when operated. This may cause passengers to trip on the …
Mitsubishi Fuso Aero Star 2017–2018
In the front body control module (vehicle control computer), the contact structure of the built-in wiper relay and its combination with the wiper motor are improper. Heat generated during relay operation can …
Mazda Axela 2015–2017
The hook portion of the clutch pedal return spring in agricultural tractors has insufficient strength and may fracture. This could result in the clutch remaining disengaged at all times, rendering the vehicle …
Kubota M7-131 2015–2017
Kubota M7131 2015–2017
Kubota M7-151 2015–2017
Kubota M7151 2015–2017
Kubota M7-171 2015–2017
+1 more
In combine harvesters, the exhaust pipe design is inadequate, allowing straw debris to accumulate between the exhaust pipe and vehicle frame. This debris obstructs heat dissipation, causing exhaust pipe surface temperature to …
Kubota ER575 2013–2018
Kubota ER590 2013–2018
Kubota ER6100 2013–2018
Kubota ER6120 2013–2018
The inflator (inflation device) for the driver-side airbag may have inadequate moisture-prevention treatment of the gas generant. Under high-humidity conditions with repeated large temperature fluctuations, the gas generant can degrade. Consequently, the …
Volkswagen CC 1.8T 2014–2016
Volkswagen cross up! 1.0 / 55kW 2014–2016
Volkswagen up! 1.0 / 55kW 2014–2016
Volkswagen Sharan 1.4/110kW 2014–2016
Volkswagen Tiguan 1.4 2014–2016
+3 more
The inflator (inflation device) of the passenger-side airbag may experience degradation of the gas generant when subjected to repeated temperature cycles in high-humidity environments. Consequently, the inflator housing may rupture upon airbag …
Ford Mustang 2006–2010
Ford Lincoln MKX 2006–2010
Driver-side or passenger-side airbag inflators may have inadequate moisture protection of the gas generant. Repeated temperature cycling in high-humidity environments can degrade the gas generant, potentially causing inflator container rupture during airbag …
Citroen C3 2014–2017
Citroen C4 2014–2017
Citroen DS3 2014–2017
Citroen DS4 2014–2017
Citroen DS5 2014–2017
Due to improper tightening work instructions for the left and right side airbag sensor mounting nuts, some nuts are not properly secured. As a result, the nuts may loosen due to driving …
Porsche 718 Boxster 2017–2018
Porsche 718 Boxster GTS 2017–2018
Porsche 718 Boxster S 2017–2018
Porsche 718 Cayman 2017–2018
Porsche 718 Cayman S 2017–2018
+11 more
In the engine compartment, the routing of the right front brake pipe is improper, causing it to interfere with the engine coolant hose retaining band due to driving vibrations and other factors. …
Alfa Romeo Alfa Giulia 2017–2018
In the driver-side SRS airbag inflator, the desiccant was assembled in a moisture-saturated state during manufacturing. Repeated environmental temperature changes cause the gas generant to degrade. During airbag deployment, internal pressure in …
Honda MDX 2001–2006
Honda Lagreat 2001–2006
In the driver-side SRS airbag inflator, the desiccant was assembled in a moisture-saturated state during manufacturing. Repeated environmental temperature changes can cause degradation of the gas generant. This may result in abnormal …
Honda Inspire 2001–2005
Honda Element 2001–2005
Honda Saber 2001–2005