Before you buy, check it isn't under a dangerous recall.

The panoramic sliding roof interior lighting has an inadequately designed electrical circuit fuse. If the sliding roof drain becomes blocked by external factors, water may infiltrate the interior lighting module circuit, causing …

In the parking brake system, due to inadequate assembly work instructions, the connection between the brake lever and brake cable lacks a lock-nut. Consequently, vibration during operation may loosen this connection, increasing …

In the rear right and center seat belts, improper parts supply during vehicle assembly resulted in some units being equipped with buckles of incorrect belt length. This may fail to provide adequate …

Certain wheels for single tires on trailers have scratches due to inadequate manufacturing process control. These scratches can initiate cracks, leading to air leakage, and in worst cases, render the vehicle unable …

The brake light switch uses an inappropriate contact design. Silicone gas volatilized from vehicle interior cleaning products and cosmetics can form an insulating film on the contact surfaces, resulting in poor electrical …

In the optional ski bag, improper stitching of the belt that secures the bag to the seat belt buckle results in insufficient tensile strength. In the event of an accident or similar …

Run-flat tires may develop cracks in the sidewall inner reinforcement layer due to improper assembly procedures during tire-to-wheel mounting. Continued use can result in abnormal noise and vibration, and in the worst …

On large buses equipped with optional front door glass heaters, improper fixation of the heater wiring causes localized bending of the wiring at the arm section (upper horizontal bar) during door opening …

On large buses, an improperly selected fuse is used in the optional front door glass heater circuit. The fuse holder may melt due to elevated temperature at the fuse terminal connections. Continued …

In combine harvesters, fuel hoses are inadequately secured and may contact rotating components such as drive belts and pulleys. This can result in fuel hose damage and fuel leakage.

In the diesel engine of a combine harvester, improper fuel injection control in the engine control computer results in insufficient pre-injection fuel quantity, causing unburned substances to develop during combustion. When the …

(1) Insufficient structural analysis of the exhaust pipe results in inability to withstand exhaust gas pressure fluctuations during high-load operation, risking pipe fracture and exhaust gas leakage. (2) Inadequate wire strength in …

(1) Insufficient strength design of the exhaust pipe results in inability to withstand pressure fluctuations from exhaust gases during high-load operation, potentially causing exhaust pipe fracture and exhaust gas leakage. (2) Insufficient …

The hydraulic clutch hose has insufficient thermal impact assessment. Heat from the engine and other sources may cause internal pressure to decrease in the hose. This results in increased clutch stroke, and …

The cam chain tensioner mounted on the cylinder block is set to an inadequate tightening torque, which may cause the tensioner to loosen due to running vibration and similar factors. As a …

Engine oil cooler hose connections on some units lack sufficient strength due to inadequate vibration analysis and testing. Vibration during operation may damage these connections, potentially resulting in engine oil leakage.

In the exhaust emission control system of wheel loaders, the urea water piping routing in the selective catalytic reduction (SCR) system may be inadequate, preventing proper distance from the high-temperature section of …

The relief valve of the gear pump used for cargo discharge on tank lorries has improper valve machining, which may cause elevated pressure in the piping during discharge operations. Consequently, cargo may …

The in-vehicle communication controller's control program is inadequate. When the ignition switch is turned off, the controller's communication function may stop, preventing fault data from being read by external diagnostic equipment. Additionally, …

In custom-spec spare tire carriers for medium-duty trucks, improper welding may cause cracks at the joint. The affected spare tire carrier may fracture and detach due to vibration, potentially obstructing other traffic.

In small buses, a label indicating the type of brake fluid is not affixed because there is no instruction to attach the label.

The vehicle speed sensor incorporated in the powertrain lacks sufficient consideration for external magnetic field effects. When the powertrain becomes temporarily magnetized by electromagnets or similar equipment used for transporting metal scrap, …

The vehicle speed sensor integrated into the power transmission system has insufficient solder at the internal circuit board. Solder cracks may develop during use, causing temporary conduction failure at the solder joint. …

In the braking system of wheel cranes, brake pipe fittings with improper dimensions have been tightened to insufficient threading depth. Continued use in this condition may result in brake fluid leakage from …

In the electric tailgate, the clip securing the pretension spring's outer tube lacks sufficient strength. When outer tube operation is obstructed by icing or similar conditions, this clip may fracture. As a …

In diesel engine fuel hoses, improper manufacturing machine settings may cause cracks to develop inside the hose. Fuel pressure can cause these cracks to propagate, potentially resulting in fuel leakage from the …

In wheel crane fuel tanks, the mounting bolts of the fuel pump configured as an optional component have improper dimensions, causing the bolt tips to contact the top surface of the fuel …

The control program of the diesel engine control unit has insufficient consideration for extreme cold conditions, which may affect exhaust gas characteristics. As a result, exhaust emissions may fail to meet regulatory …

The exhaust temperature sensor in diesel engines has insufficient durability due to inadequate durability assessment. The sensor may be damaged by running vibration and heat. As a result, the engine warning light …

The Electronic Stability Program (ESP) control unit has an inadequate control program, which may prevent the ESP from activating after engine start. If the ESP does not activate, the electronic parking brake …