Before you buy, check it isn't under a dangerous recall.

The passenger airbag inflator lacks adequate moisture protection of the gas generant, causing degradation due to repeated temperature and humidity cycling. This may result in inflator container rupture during airbag deployment.

In the torque converter of the continuously variable transmission (CVT), improper manufacturing of the internal bearing results in an uneven sliding surface. During use, this unevenness causes abnormal wear and potential fracture …

The passenger-side airbag inflator lacks adequate moisture protection for its gas generant, causing degradation through repeated temperature and humidity cycles. This may result in inflator container rupture during airbag deployment.

The inflator (inflation device) for the passenger-side airbag has inadequate moisture prevention of the gas-generating agent, which may deteriorate due to repeated temperature and humidity cycles. This creates a risk of inflator …

The passenger-side airbag inflator lacks adequate moisture protection for its gas generant, which may degrade due to repeated temperature and humidity cycles. This can cause the inflator container to rupture during airbag …

The inflator for the passenger-side airbag has inadequate moisture protection of the gas generant, which may degrade due to repeated temperature and humidity cycling. As a result, the inflator container may rupture …

The front propeller shaft's universal joint has defective manufacturing, allowing water and mud to enter the bearing area. Corrosion of the bearing by ingressed water and mud can result in abnormal noise …

Due to improper manufacturing of the fuel supply pipe, the interior of the pipe at the connector coupling attachment point may be damaged. This can cause gaps at the connector coupling attachment, …

The transmission shift lever returns to the center position after selecting a shift position, preventing the driver from shifting to Park range even when attempting to do so before the vehicle stops. …

The inflator of the passenger front airbag may have an improperly formulated igniter due to inadequate manufacturing control. Consequently, the passenger front airbag may fail to deploy upon collision, potentially causing severe …

Improper attachment of the bumper-damping device relay lever results in some units where the mounting bolts and nuts are not tightened to the specified torque. Consequently, the mounting bolts and nuts may …

The lower handlebar holder on the steering device has insufficient application of threadlocker on the stud bolts. Additionally, due to improper paint specification on the holder seating surface, repeated heavy loads from …

Due to improper attachment of the engine to the vehicle body, the air conditioning hose may contact the heat shield of the exhaust pipe. This can cause the air conditioning hose to …

The right front seat may have improperly manufactured seat rails with unopened position adjustment grooves. As a result, the seat may not be properly secured, and in the worst case, the seat …

On the front right seat, improper manufacturing of the seat rail has resulted in some units where the seat position adjustment groove is not open. Consequently, the seat may not be properly …

The auto-leveling control computer program for the headlights is defective. When the vehicle tilts rearward due to passengers occupying all seats, the optical axis may not adjust correctly. This can cause the …

The hydraulic hose of the power steering system may become disconnected due to improper crimping of the rubber hose and the fitting. When hydraulic pressure is applied through repeated steering operations, the …

In the engine, the onboard diagnostic program in the control computer is inappropriate, which may prevent fault detection when the intake air temperature sensor malfunctions. As a result, the engine warning light …

Some countershafts have developed fine cracks due to improper distortion correction processing after heat treatment. Repeated abrupt downshifts at high speeds can propagate these cracks, leading to shaft fracture and loss of …

On four-axle container dedicated vehicles, the electrical circuit of a work lamp (non-operational during driving) mounted at the rear of the vehicle is improperly configured, which may cause it to be mistaken …

On four-axle container dedicated vehicles, the upper fender geometry on the 2nd axle and 3rd and 4th axles is inappropriate, causing rotating components to protrude from these areas. This does not comply …

Due to improper assembly instructions for the rear suspension arm in the damper assembly, the rear suspension arm mounting bolts/nuts are tightened beyond the specified torque. Continued use in this condition may …

In the electric power steering control unit, the manufacturing process of the circuit board is improper, resulting in some units where terminal welding is not secure. Consequently, terminal welds may separate, causing …

Certain replacement inflator units for the driver-side airbag have inadequate moisture prevention for the gas generator. If a vehicle continues to use such an inflator after replacement during repair, the gas generator …

The front lower arm ball joint bolt has inadequate corrosion protection design. During use, the bolt may corrode, reducing its strength and causing fracture. This can result in separation of the lower …

The bolt and nut fastening the front strut to the knuckle are improperly tightened, with some nuts not secured to the specified torque. Continued use in this condition may cause the knuckle …

The control program of the cell monitor unit, which measures battery voltage and temperature in the traction battery, is inappropriate. When the vehicle rolls backward during acceleration on an uphill slope while …

The passenger-side airbag inflator may have inadequate moisture prevention of the gas generant. Repeated large temperature fluctuations in high-humidity environments can degrade the gas generant, potentially causing the inflator container to rupture …

In the electric power steering system, the manufacturing process of the circuit board within the control unit is inadequate, and some units have unreliable solder joints at the terminal connections. Consequently, the …

The electrical wiring of the wipers has improper fastening instructions during vehicle assembly, which may cause the wiring to interfere with the wiper linkage during wiper operation. This may result in wiring …