Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
10646 recalls on record · page 135 of 355
In light-duty trucks, the edge processing of the bracket securing the instrument panel is inadequate, causing interference with wire harnesses routed in the surrounding area. Vibration during operation can damage the insulation, …
In small trucks, when the manual parking brake lever is pulled up, the teeth of the lever holding mechanism may rarely balance against each other, preventing the lever from securing firmly. Subsequently, …
Certain manual transmission vehicles have insufficient strength in the gear shift rear shaft. Repeated shifting operations can cause cracks to develop in the gear shift rear shaft. Continued use may result in …
The engine control ECU has an inadequate idle control program. When the crankshaft angle sensor output signal experiences temporary disturbance or momentary interruption during engine operation detection, ignition and fuel injection may …
The lifting link for driver seat height adjustment lacks sufficient strength, and the push nut retaining method for the lifting link is improper. This can cause cracks in the lifting link or …
The mounting bolts of the fuel delivery pipe lack sufficient corrosion resistance, and may fracture due to stress corrosion cracking. This can create a gap at the connection between the fuel delivery …
Side airbag inflators may have improperly formulated ignition charges due to inadequate manufacturing controls. Consequently, side airbags may fail to deploy upon collision, potentially causing severe injury to occupants.
The airbag inflator manufacturing process has inadequate quality control, resulting in some units with igniter composition not meeting design specifications. Consequently, airbags may fail to deploy upon collision, potentially causing severe occupant …
In side airbag inflators, improper manufacturing controls have resulted in some units where the igniter composition deviates from design specifications. Consequently, side airbags may fail to deploy upon collision, potentially causing excessive …
Inadequate rust-preventive treatment of the fuel tank has caused the primer coat to peel away due to welding heat in some units. Continued use in this condition may result in fuel tank …
In the hydraulic gear pump of the wheel crane, the tie bolts that constitute the gear pump have insufficient strength, and cracks may develop due to vibration during travel and other operations. …
The throttle cable waterproof boot was manufactured improperly using materials that deviate from design specifications. Consequently, the boot deteriorates and sustains damage prematurely, allowing rainwater and other moisture to infiltrate the cable …
The inflator (inflation device) of the passenger-side airbag has inadequate moisture prevention for the gas propellant. Repeated temperature and humidity changes may cause degradation of the gas propellant. As a result, the …
On large tour buses, repeated prolonged flashing of the turn signal indicator may cause the orange cap on the rear turn signal indicator to melt. Continued operation in this condition may result …
In medium-sized route buses, the rubber component used in the starter has inappropriate material properties, and the flywheel ring gear has insufficient wear margin. Frequent engine starting via the idle stop-and-start system …
On large transit buses, the rubber component material used in the starter is inappropriate, and the flywheel ring gear lacks adequate wear tolerance. Frequent engine starting via the idle stop & start …
In the vacuum pump of the brake booster, improper manufacturing of the pump has resulted in foreign matter remaining inside some units. When foreign matter blocks the lubrication oil passage, inadequate lubrication …
Medium-duty trucks are equipped with windshields manufactured improperly, failing to meet the standard for visible light transmittance, resulting in non-compliance with safety standards.
The muffler on agricultural tractors has insufficient strength against thermal fatigue. Engine exhaust heat and vibration may cause cracks to develop in the muffler. Exhaust gas leaks from the cracked areas, and …
In the continuously variable transmission (CVT), improper control of the control unit causes delayed clutch engagement within the CVT, resulting in loss of driving force during acceleration. Consequently, when releasing the brake …
Due to inadequate manufacturing control of the transmission control module, some units have had control programs with different specifications written to them. As a result, when attempting to perform fault diagnosis with …
The passenger-side airbag inflator may have inadequate moisture protection of the gas generant. Repeated large temperature changes in high-humidity environments can cause degradation of the gas generant, potentially resulting in inflator housing …
The pump within the ABS actuator may have a damaged internal seal during assembly due to improper adjustment of the assembly equipment. This can result in insufficient brake fluid discharge pressure during …
In the securing device of a container semi-trailer, the welding of the bracket connecting the rod that links the left and right twist locks is inadequate, and the weld may fracture during …
(2) In engine ECUs of vehicles equipped with idle-stop function, the engine control program is inadequate, which may prevent proper catalyst degradation diagnosis from being performed. Consequently, the warning light may not …
(1) In the engine starting system (starter), due to an inappropriate engine control program, shift operation immediately after engine cranking begins can cause the starter motor pinion gear to be forcibly engaged …
In the passenger seat, the control program of the occupant detection system control unit is improper. When an occupant sits on the edge of the seat and remains stationary for an extended …
The seat belt feeder control unit software in the front left and right seat belts is inappropriate, causing the seat belt feeder to malfunction. The seat belt feeder may not stop at …
In large trucks, the brake control unit's control program is inappropriate, causing the Electronic Vehicle Stability Control (EVSC) system to fail to operate, resulting in non-compliance with safety standards.
Improper routing design of electrical wiring causes interference between the main harness and the anti-lock brake system (ABS) modulator in some vehicles. Continued use in this condition may damage the main harness …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.