Before you buy, check it isn't under a dangerous recall.

Improper torque specifications for through bolts in the starter can cause the bolts to loosen over time, resulting in misalignment of internal components and reduced starter output. Continued operation may lead to …

Steel disk wheels may have shape defects due to improper press equipment management, resulting in insufficient weld strength between the disk and rim. This can cause cracks in the welded area, potentially …

(2) The rear left seat belt buckle has an inadequate retention structure, which can cause it to fall inside the seat, preventing seat reclining operation. If reclining is attempted in this condition, …

(1) In the AHS (Adaptive High Beam System) of the driving support device, due to an inappropriate control program, the high beam may reignite immediately after automatic shutoff, which can disable beam …

In MT (manual transmission) vehicles, the meter panel design is inappropriate, lacking a display device to indicate the automatic control state of the driving headlight (high beam) to the driver. Therefore, it …

In the combination meter (full LCD type), the control program is inappropriate, which may prevent the startup control for displaying the meter's LCD screen from completing. As a result, the speedometer and …

The power conversion device (inverter) has an improper control program. When the push-button start is turned on shortly after being turned off, the inverter may fail to activate. This prevents engine restart …

(1) In the transmission control computer, due to an inappropriate control program, when firmly applying the brake during gear shifting or engine restart from EV driving mode, the engaged clutch may not …

In the engine, the manufacturing process of the right-side crankcase cover is defective, causing paint to adhere to the sealing plug press-fit section. Due to engine heat, the retention force of the …

In fire service two-wheelers, the electrical wiring connection within the right-side siren has been incorrectly wired due to improper schematic documentation. As a result, the siren output may not meet safety standards.

In police vehicles, due to improper schematic instructions for the electrical wiring connection points inside the right siren, the electrical wiring has been incorrectly connected in reverse polarity. As a result, the …

Due to inadequate strength analysis of the exhaust pipe mounting bracket in the wheel carrier noise prevention device, the exhaust pipe resonates at specific engine speeds, which may cause cracks to develop …

In trailers equipped with lift axle functionality, the clamping plate securing the lift air spring of the lift device may fracture due to insufficient strength, risking detachment of lift device components.

The engine control ECU for asphalt finishers contains improper correction value inputs for device variations in injectors and other components. As a result, performance compliance with the designated specification cannot be guaranteed, …

In the electric servo brake system's brake operating simulator, an inappropriate manufacturing process allows assembly oil used during production to infiltrate the pressure sensor. This causes corrosion of the resistance element within …

In the electric servo brake system's brake operating simulator, due to inadequate manufacturing processes, assembly oil used during production may enter the pressure sensor. Consequently, the resistance element within the sensor may …

Due to the use of defective mirror housings in the left and right back mirrors, the lens may detach from the mirror housing. This reduces visibility and may cause vehicle collisions.

(3) In mechanical automatic transmissions (AGS), the brush material of the oil pump drive motor is inappropriate, causing brush expansion and sliding failure under high-temperature, high-humidity conditions. Continued operation in this state …

In the joint section between the oil pump and oil pump drive motor of the mechanical automatic transmission (AGS), the ventilation structure with the external environment was inadequate. If oil seeps from …

(1) In the clutch cable of the mechanical automatic transmission (AGS), the waterproof covering structure is inadequate, which may cause corrosion on the inner wire. If use continues in this condition, the …

The battery management unit of the traction battery may incorrectly determine normal signals transmitted from the battery as a malfunction. This may cause warning lights to illuminate, warning messages to display, and …

In the air spring strut of the suspension system, improper machining during manufacturing may result in the retention clip groove not being machined correctly. As a result, the retention clip may not …

Milled brake levers have dimensional accuracy issues with the control pin inside the brake lever that connects to the master cylinder. This can result in insufficient brake system pressure adjustment, and in …

The electric coolant pump for the air conditioning system has inadequate seal design, resulting in insufficient sealing performance. Moisture enters the pump's control unit, potentially causing short circuits inside the pump. This …

The daytime running light control program is defective, causing the lights to remain on when low-beam headlights are activated. If the daytime running lights are not deactivated when low-beam headlights are on, …

The coolant joint may fracture during operation due to insufficient material strength resulting from design and manufacturing defects. This can cause coolant leakage. In severe cases, leaked coolant may contact riders causing …

The control unit software for headlights, brake lights, cabin interior lights, air conditioning, and doors is defective. It may detect an internal current surge and trigger the safety function, causing control signals …

The turn signal indicators (signal lamps) on the affected vehicles may develop cracks in the lens due to inadequate component control during manufacturing, resulting in improper heat treatment of the lens. This …

Certain cylinder head bolts in the engine have inadequate strength due to improper heat treatment during manufacturing. These bolts may fracture, causing partial loosening of the joint between the cylinder head and …

In the 48V ground wiring within the engine compartment, improper assembly instructions during manufacturing result in some body ground terminal point nuts not being fastened to the specified torque. Consequently, the nuts …