Before you buy, check it isn't under a dangerous recall.

In rear window frames, improper installation during manufacturing has resulted in trim bars that are not properly secured. This can cause the trim bar to detach from the rear window frame during …

The air conditioning evaporator drain hose may be improperly assembled, allowing condensation to leak into the vehicle interior. This can result in water accumulation beneath the floor, causing corrosion and electrical short …

Due to an improper control program in the voltage converter, temporary communication failures between the server and diagnostic scanner (scan tool) during connection cause the converter to incorrectly diagnose a fault and …

Sliding roof glass panels may have insufficient adhesive strength due to inadequate manufacturing controls. This can cause the glass panel to lift, and in the worst case, detach due to wind pressure …

Heavy-duty trucks equipped with 6R20 engines have improper engine harness assembly, causing the harness to make strong contact with the harness-fixing bracket. Engine vibration causes wear and damage at the bracket contact …

On van-type wing vehicles, the center beam mounting bracket welds on the upper rear frame are inadequately welded, resulting in insufficient strength in some vehicles. Repeated wing opening and closing can cause …

The front spindle of agricultural tractors has insufficient strength due to inadequate design-phase evaluation. Consequently, cracks may develop in the front spindle due to repeated turning operations when front weights or front …

In small-sized rotary compactor trucks, improper routing of wiring on the right side within the high-mount rear panel may cause the wiring to contact and break when opening and closing the rear …

In the electric powertrain ECU, due to improper power control programming, safe mode activation occurs when electric compressor insulation failure is detected, resulting in loss of propulsion.

Front ABS sensor harness bracket bolts on the steering knuckle may not be tightened to the specified torque due to improper assembly during vehicle manufacturing. Continued use could result in bolt loosening …

The intermediate shaft has improper assembly work during vehicle assembly, resulting in bolts fastening to the steering gear not being tightened to specification torque. Continued use may cause bolt loosening, and in …

In the front suspension, improper assembly work during vehicle production has resulted in some units where the bolt and nut fastening the upper arm ball joint to the steering knuckle are not …

The engine control computer has inadequate throttle pedal diagnostic control programming from development and insufficient fail-safe control evaluation. Under specific throttle pedal operations, the throttle pedal sensor may be incorrectly diagnosed as …

Plastic coolant pipes, which are part of the coolant circulation circuit, were manufactured using a material with low heat resistance. When coolant circulation stops, such as due to water pump failure, these …

In the parking brake of agricultural chemical spray vehicles, inadequate manufacturing control of the hook and gear that hold the lever in the fixed position results in insufficient strength of the hook …

When wheel loaders are operated in cold environments, the engine oil separator freezes. Continued operation causes engine oil to flow backward into the combustion chamber, resulting in engine over-speed that prevents proper …

The permanent-magnet retarder (auxiliary brake) on the rear axle is actuated by air pressure. A design error in the connector terminal configuration of the chassis harness connected to the retarder harness results …

In slide-up seats equipped with seat heaters, the thermistor (temperature control sensor) for the seat heater is mounted in an improper position, causing delayed entry into temperature control during seat heater operation, …

The waterproof structure of the connector linking the O₂ sensor wiring in the main harness is inadequate. Water accumulating in the connector during rain operation can be drawn into the connector interior …

In trailers equipped with lift-axle functionality, insufficient strength analysis resulted in inadequate strength of the clamping plate that secures the lift air spring of the lift device, which may fracture and cause …

The trailing arms in the front and rear suspension have insufficient corrosion resistance due to inadequate material selection during design. Extended use results in corrosion at the arm joints, causing cracking accompanied …

Due to improper assembly procedures for the left and right rear seat belts, portions of the seat belt may be trapped beneath the C-pillar cover. Consequently, the trapped seat belt may be …

The impeller (resin fan wheel) of the low-pressure fuel pump may swell and deform due to improper molding conditions resulting in low resin density, causing swelling from fuel exposure. This can cause …

The surround view cameras may experience poor contact at the coaxial cable connection due to improper manufacturing process, resulting in loss of camera image around the vehicle. This may prevent the driver …

The pump bracket and center bearing bracket that connects the drive shafts of the cargo discharge pump on aluminum tank lorries have insufficient rigidity due to inadequate stiffness analysis during design. Continued …

The fuel pump impeller (plastic rotor) may have been molded under improper conditions, resulting in low resin density. This causes the impeller to swell and deform when exposed to fuel, potentially contacting …

In the power transfer unit, due to improper control programming, when the unit fails due to excessive load driving on rough terrain or similar conditions, the safe mode does not function. Power …

The electric coolant pump for the air conditioning system has an inadequate design for venting internal negative pressure, allowing moisture to enter the electrical connector inside the pump and potentially causing short …

In the braking system, the front wheel brake hose was not properly installed in the correct position due to improper assembly work on the vehicle body. As a result, the hose contacts …

In the urea SCR system of the exhaust gas control device, the heater wiring for the urea water piping is improperly processed and secured. Due to vibration during driving, this wiring may …