Before you buy, check it isn't under a dangerous recall.

The engine control unit's control program is inadequate, causing the system to misinterpret load-induced rpm fluctuation during idle as a misfire, resulting in cylinder combustion shutdown, illumination of the engine warning light …

In the front trunk, the design of the secondary latch mounting is inappropriate, resulting in some units not achieving the specified fit. Consequently, if the driver unintentionally releases the primary latch, the …

1. The engine side cover structure of the shovel loader is inadequate, causing the pin that secures the side cover to not seat properly in the latch. Continued operation may result in …

1. The engine side cover structure of the shovel loader is improperly designed, causing the pin that secures the side cover to not engage properly with the latch. Continued operation may result …

On wipers for battery-powered forklifts, the spring attached to the wiper arm has an improper length specification, causing the wiper to press strongly against the front glass. Continued use may result in …

In the standing assist function, improper hardness of the caliper pad and surface roughness of the disc may cause the pad to remain in contact with the disc even after the standing …

In forklift engines, improper mold management during cylinder head manufacturing results in combustion chamber geometry that exceeds tolerance specifications. This prevents proper air-fuel mixture formation during gasoline operation, causing combustion defects and …

In forklift engines, improper mold management during cylinder head manufacturing results in combustion chamber geometry exceeding tolerance limits. This prevents proper air-fuel mixture formation when using gasoline fuel, causing combustion defects and …

Battery Management Electronics (SME) software is deficient, potentially causing system misdiagnosis. As a result, though rare, charging may stop or the high-voltage system may shut down, reducing motor output and response, and …

The BCM (Brake Control Module) has improper program design, which may cause false error detection during system diagnostic testing. This can result in illumination of brake warning lights and deactivation of ABS …

Some tail lights have an answer-back function where the tail light illuminates with progressively changing luminous intensity synchronized to vehicle lock/unlock operations. However, due to an inappropriate illumination program, the total operation …

Fastening bolts on the front suspension arm and subframe may be insufficiently tightened and could loosen during use. This may cause abnormal noise during driving and, in the worst case, the suspension …

The bolts securing the impactor to the front subframe are inadequately tightened, which may cause them to loosen during use. This can result in abnormal noise during driving and, in the worst …

The diesel engine exhaust gas recirculation (EGR) module may experience coolant leakage due to aging. When this occurs, soot contained in the exhaust gas mixes with the coolant and accumulates inside the …

In diesel engine exhaust gas recirculation (EGR) modules, coolant may leak due to aging. When this occurs, soot contained in exhaust gas mixes with the coolant and accumulates inside the EGR module. …

The diesel engine exhaust gas recirculation (EGR) module may develop coolant leaks due to aging. When this occurs, soot contained in exhaust gas mixes with the coolant and accumulates inside the EGR …

The waterproof seal at the wiring inlet of the tail lamp unit has inadequate performance, allowing water ingress into the unit and causing corrosion at the LED connection. Continued operation in this …

In replacement parts for VR38-type engines, improper calibration of the equipment measuring machine for crank hole machining resulted in some crank holes being machined smaller than specification. Consequently, in extremely cold environments, …

The body integrated control computer in the fuse block may experience internal short circuits due to improper capacitor manufacturing processes. If use continues in this condition, the fuse may blow, resulting in …

The seat module software is inappropriate, preventing correct detection of seat position. This causes airbag warning light and check control message illumination, and may result in failure of passenger airbag, knee airbag, …

The attachment clips on the resin cover inside the rear fender have an inappropriate shape, which may cause the clips to loosen due to driving vibration and other factors. This can result …

In the cooling system, the cooling fan motor may experience degraded performance due to repeated excessive heat exposure from the engine. Continued operation in this condition risks engine overheating, which in severe …

The Radio Frequency Hub Module (RFHM) is overly sensitive to noise in the driving environment and may incorrectly detect a system malfunction. This can cause a keyless entry failure warning to display …

Some vehicles were not properly inspected for parking brake force compliance with safety standards because the test equipment settings at the vehicle manufacturing plant's outgoing inspection were inappropriate.

Large and medium-sized tour buses may develop corrosion on the metal brackets that secure the plastic cover of the ceiling air conditioning unit due to inadequate rust protection measures. If operation continues …

In graders, peak pressure of the hydrostatic transmission was insufficiently evaluated. When the forward/reverse selector switch is switched from reverse to forward before the vehicle comes to a complete stop, hydraulic circuit …

The front camera, a component of the driving assistance system, may experience conduction failures due to inadequate semiconductor manufacturing controls, causing the camera to stop operating. As a result, the driving assistance …

In the automatic transmission, due to improper manufacturing process, the cut surface of the oil drain plug mounting area is rough in some units. This causes oil lubricating the automatic transmission to …

In light-duty truck engines, excessive clearance exists between the vacuum pump coupling and camshaft in some units. Continued operation causes abnormal wear at the coupling and camshaft fitting, resulting in coupling failure …

In high-voltage batteries, improper welding of battery cell electrode terminals may occur. This causes increased resistance, leading to degraded battery performance, illumination of warning lights, and limitation or reduction of motor output. …