Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 118 of 175
The front axle of large non-step buses has insufficient strength. Repeated rolling and lock-to-lock steering operations over extended periods can cause cracks to develop in the axle. Continued use in this condition …
Due to improper programming in the Engine Control Unit (PCM), engine idle speed may drop during steering operations and other maneuvers, with the potential risk of engine stall while driving.
Improper routing of the main harness may cause it to contact the bolt tip of the hydraulic rear suspension adjustment device or burrs on the frame weld. Continued use in this condition …
The front wheel brake line fastening method is inadequate, which may cause stress at both ends of the brake line due to vibration during operation. This may result in cracks forming in …
The electrical wiring connector inside the instrument panel is mounted in an improper position, allowing condensation from the air conditioning duct to enter the connector interior. Continued use in this condition may …
The acceleration sensor that detects the operation of the hydraulic-controlled front suspension may have improper solder processing on the circuit board, potentially preventing accurate measurement of vehicle height changes. This can cause …
The combination of motor brush material and steering gear ratio in the electric power steering (EPS) system is inappropriate. Repeated full lock steering operations cause excessive current to flow through the internal …
In the brake booster of dual-mode rail/road vehicles, defective welds in vacuum piping and incorrect vacuum hose assembly have been identified. Insufficient vacuum supply may result, potentially causing extended braking distance in …
The pivot pin for the secondary-axis steering lever in the steering device has improper machining at the corners, resulting in rough surfaces on some units. This may reduce the strength of the …
The fulcrum pin of the first-axis steering lever in the steering apparatus has insufficient fatigue strength, and cracks may develop in the pin. If use continues in this condition, the pin may …
Insufficient clearance between the front wheel brake air line and parking brake air line causes interference in some vehicles. Continued use in this condition may result in the front wheel brake air …
The ratchet engaging surface that holds the parking brake lever has an improper shape. Repeated parking brake operation causes the engaging surface on the push rod side to wear, resulting in disengagement. …
The bushing dimensions in the link mechanism that secures the stabilizer to the chassis are improper, resulting in poor sliding at the bushing during front suspension vertical movement. This can cause excessive …
In the manufacturing process of the CVT (Continuously Variable Transmission) oil cooler hose, some units have inadequate cleaning treatment. As a result, engine vibration and other factors may cause the hose to …
During the manufacturing process of the piston cup inside the brake master cylinder, foreign matter may be present in some units. This can cause cracks in the piston cup, resulting in reduced …
The electronic circuit controlling the washer fluid freeze-prevention heater may have foreign matter adhered during manufacturing. This circuit could short, potentially resulting in fire.
The electronic circuit controlling the windshield washer fluid freeze-protection heater may have foreign material adhered to it from the manufacturing process. This can cause the circuit to short, potentially resulting in fire.
The manufacturing process for U-bolts securing the rear axle to the leaf spring was improper, causing cracks to develop in the bolts. These bolts are subject to corrosion from de-icing agents and …
The rear-wheel brake line in the engine room is improperly secured and may contact the lower universal joint of the steering shaft. Continued use could result in brake line damage, brake fluid …
During tire assembly, wheel nuts may be insufficiently tightened due to improper fastening torque application. Continued use may result in nut loosening, abnormal noise generation, and in worst cases, wheel detachment.
The fuel tank filler opening on certain units has improper molding at the manufacturing stage, resulting in gaps between the tank cap mating surface. This can cause fuel leakage from the mating …
The relay emergency valve, which controls air supply and air pressure in the trailer air brake system, has no designated periodic replacement parts or repair parts specified, resulting in no component replacement …
In dump-equipped vehicles, the transmission cable was relocated during dump wire routing, resulting in insufficient clearance between the transmission cable and chassis harness in some units. Consequently, running vibration can cause interference …
Some vehicles have insufficient clearance between the harness and wiper linkage within the instrument panel. During wiper operation, the wiper linkage may contact the harness, potentially damaging it and resulting in inadvertent …
The hardening treatment of the vane tip surfaces in the hydraulic power steering pump is inadequate, causing vane wear and wear debris to accumulate within the pump and oil tank. Continued use …
Due to improper casting of the fuel pump's pump cover, the internal surface of the pump cover may have burrs in some units. These burrs can detach due to vibration and become …
Due to improper electrical circuitry to the combination switch, if the fog light is illuminated while the harness to the tail light is in a short-circuit condition, the harness inside the combination …
Some vehicles have insufficient clearance between the rear brake hydraulic line and torque converter (fluid coupling). During suspension lock (forced suspension compression and fixation to improve vehicle stability during crane operations, etc.), …
The fuel pump mounting section of the fuel tank has insufficient structural strength. Cracks may develop in the fuel pump mounting section due to tightening force during pump installation. This may result …
The integrated rear brake pedal footrest (right side) and integrated transmission footrest (left side) aftermarket optional parts have insufficient attachment strength at the mounting points to the frame, which may cause the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.