Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5227 matching recalls · page 15 of 175
At the chassis-to-body fastening points (front) of van-type trucks, inadequate work instructions and verification procedures may result in the backing plate that secures the bracket mount fastener pinching the brake line against …
Due to improper manufacturing instructions for air conditioning refrigerant, an incorrect refrigerant has been filled. Consequently, if the refrigerant leaks due to an accident or similar incident, there is a risk of …
In the engine compartment of left-hand-drive vehicles, the 48V ground wiring has improper assembly at manufacturing, resulting in nuts not being tightened to the specified torque. Consequently, vibration during operation may cause …
The transmission control unit has an inappropriate control program. Under specific cold-start conditions, when gradually re-accelerating from gentle deceleration in 7th gear, transmission internal hydraulic pressure may not increase as intended. This …
The 48V ground wiring located beneath the front passenger seat may have been improperly assembled during manufacturing, resulting in nuts not being tightened to the specified torque. This can cause loss of …
Power fuses have manufacturing defects resulting in cracks in the fuse element or separated solder joints. When cracks are present, driving vibrations may cause fuse element breakage, disabling the SRS system or …
In right-hand drive vehicles, the electric power steering control program is inappropriate. If a malfunction occurs in the electric power steering system, power assist may cease to operate or steering vibration may …
The driver assistance system control unit had insufficient verification during software development. When cornering using the active lane-keeping assist function, speed may exceed design parameters. As a result, maximum lateral acceleration does …
The transmission control computer has improper clutch control during deceleration, which may cause delayed clutch disengagement timing or unintended clutch engagement. This can result in decreased engine speed during deceleration, and in …
The engine control computer has improper learning conditions for fuel vapor concentration, causing it to learn when the purge valve is closed and misjudge the concentration as lower than actual. When fuel …
The Smart Brake Support control program in the vehicle control computer is inappropriate. When there are angled metal walls or similar structures beside the road, the forward-moving left/right proximity detection function may …
The right rear lighting assembly may have compromised sealing within the light case due to improper component handling during manufacturing. As a result, water ingress and corrosion may occur in the light …
In the integrated brake unit, inadequate manufacturing controls have resulted in foreign matter adhering to the motor sensor circuit board. This causes electrical contact failures, resulting in brake warning light illumination and …
Certain Air Pressure Modulator (APM) units contain semiconductors that were insufficiently evaluated and verified during design changes, failing to meet durability and reliability standards. Continued use may result in premature semiconductor degradation, …
The rear door handle opening switch lacks adequate waterproofing. Exposure to large quantities of water during washing can allow water to enter the switch interior. Continued use in this state may cause …
In agricultural tractors, the main harness routing is improperly installed, causing contact with the DPF in some units. Continued operation in this condition risks harness damage, potentially resulting in loss of power …
In the integrated brake unit, improper manufacturing control has resulted in foreign material adhesion on the motor sensor circuit board. This causes electrical contact failure, resulting in brake warning light illumination and …
In battery-powered forklifts equipped with heaters, improper insertion procedures for the heater power harness connector have resulted in some units being inserted with terminal orientation reversed. This causes terminals to fail to …
The seal gasket used at the connection of the rear axle shaft has inadequate design. Under conditions of severe fluctuating driving torque, the seal gasket may shift slightly in the rotational direction …
The bolt hole drilling depth in the cable fastening section within the steering wheel was inappropriate, causing improper cable crimping in some vehicles when bolts are tightened. This results in poor electrical …
Front suspension top caps on certain units have inadequate fastening due to improper manufacturing. Continued use may result in top cap detachment due to driving vibration, leading to suspension malfunction and loss …
In the front brake, due to improper brake fluid filling procedure, a small amount of air bubbles may be present in the brake hydraulic system. If operation continues in this condition, when …
In the fuel system, improper assembly procedures have resulted in insufficient crimping of the single-ear hose clamp connecting the fuel hose to the fuel pump. Consequently, when high fuel pressure is applied, …
In the electric power steering system, improper work instructions during vehicle assembly at the factory caused contact between the body and internal components during assembly. As a result, internal electronic components may …
The ground wire terminal nut of the 12V battery located beneath the passenger seat may not be tightened to specification due to improper assembly during manufacturing. Vibration during driving can cause the …
Roof panels adhesively attached to the vehicle body may not have been repaired with adequate adhesive strength due to improper repair work instructions during service. This can result in progressive delamination from …
The fuel pump impeller (resin-made rotor blade) may swell and deform due to improper manufacturing when exposed to fuel. This causes the impeller to contact the pump housing, resulting in fuel pump …
In electric small trucks, due to improper VCU control programming, a communication error is mistakenly detected, causing the high-voltage system to shut down for safety reasons. As a result, the driver may …
High-voltage battery cell modules have been manufactured with improper tolerance settings, resulting in some cell modules with excessive tolerances. Under specific conditions, this can cause irregularities in charge-discharge characteristics. When affected cell …
The fuel pump impeller uses an inappropriate material, which can expand and deform due to fuel temperature. This causes excessive friction between components, resulting in fuel pump malfunction, and in the worst …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.