Public safety register · Cyprus imports
A free, searchable record of vehicle safety recalls from the markets Cyprus imports from — Japan & Ireland, plus local Cyprus notices. Search by make, model and year, and flag the fire, airbag, brake and steering defects that matter most.
5188 matching recalls · page 22 of 173
On the left and right front axles, the groove machining that retains the snap ring on the upper portion of the air spring strut is improper, which may cause the snap ring …
On leather-wrapped dashboards, improper adhesion of the leather cover near the passenger seat may obstruct airbag deployment by causing partial dashboard deformation during passenger-side airbag deployment. In the worst case, part of …
In vehicles equipped with lane change support function (LCS) on the electronic controlled steering system (UDAS), the driver assistance control unit (DACU) has improper program settings. When LCS detects a vehicle on …
The control computer for the electric parking brake has an improper brake release program, which may result in insufficient brake cable retraction. Repeated use in this condition causes the brake cable to …
The fuel supply unit mounted inside the fuel tank has insufficient internal component strength. Due to fuel pressure fluctuations, this component may rupture during vehicle operation. The ruptured component can damage the …
In the anti-jack-knife (AJK) device of full trailers and dolly-equipped semi-trailers, an improper electrical circuit causes the following malfunctions when the AJK switch in the tractor operator's cab is in the ON …
Due to manufacturing defects in the backup power capacitor of the airbag controller, internal short circuits may occur. If controller power is cut off during a collision, all airbags and seat belt …
The camera bracket adhesive process control for the pre-collision safety system (Smart Assist) camera mounted on the windshield glass is inadequate, resulting in weak adhesion in some units. Consequently, the bracket may …
Wiring harnesses in the engine compartment near the battery are routed improperly, causing contact with surrounding components. Vibration during operation or maintenance can damage the harness insulation, leading to short circuits, overheating, …
The under-engine protector has inadequate design, allowing grass to accumulate inside the protector during off-road driving. Accumulated grass may contact the exhaust pipe, potentially causing fire.
In trailers equipped with lift axle functionality, pressure values for initiating lift axle raising and lowering operations were set incorrectly, risking non-lift axles to exceed permissible axle weight limits under Road Transport …
In the ignition switch, improper fixing position of wiring causes sharp bending at maximum steering lock. Continued use may result in wiring fracture due to repeated bending, which could cause engine stall …
In the braking system, the ABS control program is inappropriate, causing excessive sensitivity to signals from the brake pressure sensor. As a result, the brake lights may illuminate and the engine may …
The bipod strut connecting the rear suspension lower portion to the frame may have insufficient hardness due to improper manufacturing process. This can cause the component to fracture, leading to a reduction …
Certain steering column module wiring connectors lack proper locking clips due to inadequate work instructions. Road vibrations during use can cause these connectors to loosen, resulting in electrical contact failures that illuminate …
The ESP control unit (electronic stability program) may have deformed exterior casing due to improper handling during vehicle assembly. This degradation of sealing performance allows moisture ingress, causing electrical failure, warning light …
Diesel engine fuel supply hoses were manufactured with incorrect release agent due to improper manufacturing instructions. This results in reduced friction on the inner wall of the hose, causing the rubber hose …
Some integral front axle carriers have inadequate rust protection, resulting in low corrosion resistance. Over time, this causes strength degradation, leading to partial fracture. In worst-case scenarios, steering may become inoperative.
The pressure relief valve in the air suspension air compressor is made of inappropriate material, which can cause corrosion and malfunction. This may result in the warning light illuminating and preventing ride …
In the camshaft chain tensioner that adjusts camshaft chain tension, internal components deteriorate with use, causing the plunger to be pushed back and potentially lock. If use continues with the plunger locked, …
Certain vehicle handlebars have inadequate weld quality, resulting in insufficient structural strength. During operation, cracks may develop at the welded joint. In the worst case, the grip portion may separate, causing loss …
In the camshaft chain tensioner that adjusts camshaft chain tension, internal components deteriorate through use, causing the plunger to be pushed back and potentially lock. If operation continues with the plunger locked, …
The speedometer (meter unit) may restart while driving due to improper control programming. During restart, the operator will be unable to confirm speed and other information necessary for operation.
The seat strap (rear seat grab handle) attached to the driver's seat of the seating equipment may have insufficient strength due to improper processing conditions during manufacturing. Continued use in this condition …
In the steering column switch, due to improper control unit programming, when system voltage drops below 6V during low battery charge conditions such as cold engine starting, an electrical fault may be …
In the in-tank unit of the fuel pump, the clearance design between the resin impeller and cover is inadequate. As a result, the resin impeller may deform due to elevated fuel temperature, …
In shovels and loaders, improper assembly of the heating element in heated fuel filters can cause the heating element to tilt and contact the sight glass. Continued operation may result in the …
In the generator, the rib height in the left crankcase cover interior where the stator coil is assembled is set improperly, causing the coil wire to contact and damage the rib, resulting …
In the driver seat seatbelt, steering column, and driver seat airbag, improper part number specifications in the replacement/repair parts catalog resulted in some vehicles being equipped with non-specification parts. Consequently, under certain …
Replacement service parts catalogs contain incorrect part number specifications for (1) driver-side seat belt or steering column, and (2)(3) driver-side airbag. Consequently, non-specification parts have been installed on some vehicles. In the …
Whether you're an owner asking "is my car affected?" or a buyer vetting a used import before you pay, these answer the questions people most often ask.