Before you buy, check it isn't under a dangerous recall.

In the engine, due to improper programming of the crankshaft sensor, the crankshaft position is not detected properly, resulting in incorrect signals being input to the engine control unit. As a result, …

The powertrain control unit, which performs communication protocol conversion between control units, has an inadequate control program that may cause the system to restart while driving. This can result in loss of …

The SRS control unit that controls airbags and other occupant restraint systems may be damaged due to improper component assembly. As a result, occupant restraint systems may fail to deploy during collision …

The press-fit method for the automatic adjustment drive pins in the front and rear wheel brake calipers is improper, which may cause the drive pins to fracture under repeated brake operation. As …

The driver-side airbag inflator may have inadequate moisture protection of the gas generant. Repeated large temperature fluctuations in high-humidity environments can cause gas generant degradation. This may result in inflator container rupture …

Due to improper manufacturing of the fuel supply pipe, the interior of the pipe at the connection coupler mounting point may be damaged. This creates gaps at the connection coupler mounting point, …

The automatic adjustment drive pins in the front and rear wheel brake calipers may fracture due to improper press-fitting method. Repeated brake operation can cause drive pin fracture. If brake pad wear …

During the manufacturing process of the front-wheel brake lever, defective products (insufficient strength) were improperly handled and mixed into regular production, resulting in some being installed on vehicles. Consequently, the brake lever …

The main harness guide that retains the main wire harness and clutch cable has an improper shape. When the handlebars are turned fully left or right, the harness may be pulled excessively. …

Due to inadequate manufacturing controls of the steering column intermediate shaft in the steering system, foreign objects (nuts) may be present in the universal joint within the shaft. As a result, during …

In the power relay of wheel loaders, the cap material is inappropriate, causing electrode surface deformation due to deterioration over time. This may result in internal short circuit, loss of main power …

The electric water pump that cools the fuel cell system has inadequate surface treatment on the drive motor magnet, causing the magnet to corrode due to cooling water. Continued use allows corrosion …

In the power relay of the shovel loader, the cap material is inappropriate, and the electrode surface may deform due to deterioration over time. This can cause internal short circuits, resulting in …

The fuel pump with fuel gauge mounted in the fuel tank may tilt when the fuel tank expands due to external temperature fluctuations and other environmental factors, as operating conditions were insufficiently …

The Brake System Module (BSM) control program is inappropriate, so when using Adaptive Cruise Control (ACC), stepping on the brake pedal may not disengage the ACC. This can result in unintended acceleration …

The inflator in the passenger-side airbag may degrade under prolonged exposure to high temperature and humidity cycles. Upon airbag deployment, the inflator container could rupture, potentially injuring occupants.

In the front suspension, some vehicles have coil springs with improper geometry, resulting in unstable contact with the spring seat. During large vehicle bouncing, the spring may shift and interfere with the …

In spiral cables attached to the steering wheel of taxi-specification vehicles, the internal structure retaining the wiring is inadequate, causing the wiring to interfere with surrounding components at large steering angles. Repeated …

In the front damper assembly, the damper shaft material and geometry are inadequate, resulting in insufficient durability of the damper shaft in some units. Consequently, repeated steering inputs may cause damper shaft …

Inadequate water sealing at the joint between the cowl louver and dash panel allows rainwater to drip onto the brake booster. This can cause rust to develop on the brake booster. If …

In the automatic clearance adjustment mechanism (strut set) between the rear wheel brake shoes and drum, improper grease application during component assembly has resulted in some adjuster bolts lacking grease on their …

The combination meter has improper circuit configuration. When the vehicle interior is exposed to moisture for extended periods, condensation may form on the meter substrate, causing the power circuit section to short. …

The instrument cluster program controlling the brake pad wear warning is inappropriate, so the warning light does not illuminate when brake pads are worn beyond the limit. Consequently, brake pads may be …

Due to improper programming in the electric power steering control unit, the power steering assist function may stop during driving. This may result in increased steering effort.

In the braking system of large trucks with dual rear-axle drive, due to improper work instructions, the air pressure test connector for the braking system was incorrectly installed in some units. As …

In combine harvesters, the exhaust pipe design is inadequate, allowing straw debris to accumulate between the exhaust pipe and vehicle frame. This debris obstructs heat dissipation, causing exhaust pipe surface temperature to …

The inflator (inflation device) for the driver-side airbag may have inadequate moisture-prevention treatment of the gas generant. Under high-humidity conditions with repeated large temperature fluctuations, the gas generant can degrade. Consequently, the …

The inflator (inflation device) of the passenger-side airbag may experience degradation of the gas generant when subjected to repeated temperature cycles in high-humidity environments. Consequently, the inflator housing may rupture upon airbag …

Driver-side or passenger-side airbag inflators may have inadequate moisture protection of the gas generant. Repeated temperature cycling in high-humidity environments can degrade the gas generant, potentially causing inflator container rupture during airbag …

Due to improper tightening work instructions for the left and right side airbag sensor mounting nuts, some nuts are not properly secured. As a result, the nuts may loosen due to driving …